Machinery's Handbook, 31st Edition
1838
SELF-THREADING SCREWS Table 5. ANSI Standard Thread and Point Dimensions for B and BP Thread Forming and BF and BT Thread Cutting Tapping Screws
ANSI/ASME B18.6.3-2013 THREAD FORMING TYPES B AND BP
D
d
P
S
L
Minimum Practical Nominal Screw Lengths Type B Type BP
Point Taper Length d
Nominal Size a or Basic Screw Diameter
Major Diameter
Minor Diameter
Point Diameter c
Thds per Inch b
90 ° Heads
Csk Heads
90 ° Heads
Csk Heads
Max. Min. Max. Min. Max. Min. Max. Min.
0 0.0600 48 0.060 0.054 0.036 0.033 0.031 0.027 0.042 0.031 1 ∕ 8 1 ∕ 8 5 ∕ 32 3 ∕ 16 1 0.0730 42 0.075 0.069 0.049 0.046 0.044 0.040 0.048 0.036 1 ∕ 8 5 ∕ 32 3 ∕ 16 7 ∕ 32 2 0.0860 32 0.088 0.082 0.064 0.060 0.058 0.054 0.062 0.047 5 ∕ 32 3 ∕ 16 1 ∕ 4 9 ∕ 32 3 0.0990 28 0.101 0.095 0.075 0.071 0.068 0.063 0.071 0.054 3 ∕ 16 7 ∕ 32 9 ∕ 32 5 ∕ 16 4 0.1120 24 0.114 0.108 0.086 0.082 0.079 0.074 0.083 0.063 3 ∕ 16 1 ∕ 4 5 ∕ 16 11 ∕ 32 5 0.1250 20 0.130 0.123 0.094 0.090 0.087 0.082 0.100 0.075 7 ∕ 32 9 ∕ 32 11 ∕ 32 13 ∕ 32 6 0.1380 20 0.139 0.132 0.104 0.099 0.095 0.089 0.100 0.075 1 ∕ 4 9 ∕ 32 3 ∕ 8 7 ∕ 16 7 0.1510 19 0.154 0.147 0.115 0.109 0.105 0.099 0.105 0.079 1 ∕ 4 5 ∕ 16 13 ∕ 32 15 ∕ 32 8 0.1640 18 0.166 0.159 0.122 0.116 0.112 0.106 0.111 0.083 9 ∕ 32 11 ∕ 32 7 ∕ 16 1 ∕ 2 10 0.1900 16 0.189 0.182 0.141 0.135 0.130 0.123 0.125 0.094 5 ∕ 16 3 ∕ 8 1 ∕ 2 19 ∕ 32 12 0.2160 14 0.215 0.208 0.164 0.157 0.152 0.145 0.143 0.107 11 ∕ 32 7 ∕ 16 9 ∕ 16 21 ∕ 32 1 ∕ 4 0.2500 14 0.246 0.237 0.192 0.185 0.179 0.171 0.143 0.107 3 ∕ 8 1 ∕ 2 21 ∕ 32 3 ∕ 4 5 ∕ 16 0.3125 12 0.315 0.306 0.244 0.236 0.230 0.222 0.167 0.125 15 ∕ 32 19 ∕ 32 27 ∕ 32 31 ∕ 32 3 ∕ 8 0.3750 12 0.380 0.371 0.309 0.299 0.293 0.285 0.167 0.125 17 ∕ 32 11 ∕ 16 15 ∕ 16 1 1 ∕ 8 7 ∕ 16 0.4375 10 0.440 0.429 0.359 0.349 0.343 0.335 0.200 0.150 5 ∕ 8 25 ∕ 32 1 1 ∕ 8 1 1 ∕ 4 1 ∕ 2 0.5000 10 0.504 0.493 0.423 0.413 0.407 0.399 0.200 0.150 11 ∕ 16 27 ∕ 32 1 1 ∕ 4 1 13 ∕ 32 a Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place shall be omitted. b The width of flat at crest of thread shall not exceed 0.004 inch for sizes up to No. 8, inclusive, and 0.006 inch for larger sizes. c Point diameters specified apply to screw threads before roll threading. d Points of screws are tapered and fluted or slotted. The flute on Type BT screws has an included angle of 90 to 95 degrees and the thread cutting edge is located above the axis of the screw. Flutes and slots extend through first full form thread beyond taper except for Type BF screw on which tapered threads may be complete at manufacturer’s option and flutes may be one pitch short of first full form thread. THREAD CUTTING TYPES BF AND BT d
D
d
P
S
L
Minimum Practical Nominal Screw Lengths
Point Taper Length d
Nominal Size a or Basic Screw Diameter
Major Diameter
Minor Diameter
Point Diameter c
Thds per Inch b
90 ° Heads
Csk Heads
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
0.060 0.054 0.036 0.033 0.031 0.027 0.042 0.031 0.075 0.069 0.049 0.046 0.044 0.040 0.048 0.036 0.088 0.082 0.064 0.060 0.058 0.054 0.062 0.047 0.101 0.095 0.075 0.071 0.068 0.063 0.071 0.054 0.114 0.108 0.086 0.082 0.079 0.074 0.083 0.063 0.130 0.123 0.094 0.090 0.087 0.082 0.100 0.075 0.139 0.132 0.104 0.099 0.095 0.089 0.100 0.075 0.154 0.147 0.115 0.109 0.105 0.099 0.105 0.079 0.166 0.159 0.122 0.116 0.112 0.106 0.111 0.083 0.189 0.182 0.141 0.135 0.130 0.123 0.125 0.094 0.215 0.208 0.164 0.157 0.152 0.145 0.143 0.107 0.246 0.237 0.192 0.185 0.179 0.171 0.143 0.107 0.315 0.306 0.244 0.236 0.230 0.222 0.167 0.125 0.380 0.371 0.309 0.299 0.293 0.285 0.167 0.125 0.440 0.429 0.359 0.349 0.343 0.335 0.200 0.150 0.504 0.493 0.423 0.413 0.407 0.399 0.200 0.150
0 0.0600 48 1 0.0730 42 2 0.0860 32 3 0.0990 28 4 0.1120 24 5 0.1250 20 6 0.1380 20 7 0.1510 19 8 0.1640 18 10 0.1900 16 12 0.2160 14 1 ∕ 4 0.2500 14 5 ∕ 16 0.3125 12 3 ∕ 8 0.3750 12 7 ∕ 16 0.4375 10 1 ∕ 2 0.5000 10
1 ∕ 8
1 ∕ 8 1 ∕ 8
5 ∕ 32 3 ∕ 16 7 ∕ 32
5 ∕ 32 3 ∕ 16 3 ∕ 16 7 ∕ 32
1 ∕ 4
9 ∕ 32 9 ∕ 32 5 ∕ 16
1 ∕ 4 1 ∕ 4
11 ∕ 32
9 ∕ 32 5 ∕ 16
3 ∕ 8
7 ∕ 16
11 ∕ 32
1 ∕ 2
3 ∕ 8
19 ∕ 32 11 ∕ 16 25 ∕ 32 27 ∕ 32
15 ∕ 32 17 ∕ 32
5 ∕ 8
11 ∕ 16
All dimensions are in inches. See Table 1 and Table 2 for thread diagrams.
Copyright 2020, Industrial Press, Inc.
ebooks.industrialpress.com
Made with FlippingBook - Share PDF online