Table 6. Thread and Point Dimensions for Type C Thread Forming Tapping Screws ANSI/ASME B18.6.3-2013, Appendix
D
P
S
L
Point Taper Length c
Determinant Lengths for Point Taper c 90 ° Heads Csk Heads
Minimum Practical Nominal Screw Lengths 90 ° Heads Csk Heads
Nominal Size a or Basic Screw Diameter
Major Diameter
Point Diameter b
For Short Screws
For Long Screws
Threads per inch
Max. 0.068 0.070 0.078 0.081 0.087 0.091 0.100 0.102 0.107 0.113 0.132 0.136 0.148 0.158 0.174 0.180 0.200 0.214 0.257 0.271 0.312 0.333 0.366 0.387 0.423 0.450
Min. 0.061 0.064 0.070 0.074 0.078 0.083 0.091 0.094 0.096 0.104 0.122 0.126 0.135 0.148 0.161 0.168 0.184 0.202 0.239 0.257 0.293 0.319 0.344 0.371 0.399 0.433
Max. 0.062 0.055 0.073 0.062 0.088 0.073 0.088 0.080 0.109 0.088 0.109 0.097 0.146 0.109 0.146 0.125 0.175 0.125 0.194 0.146 0.219 0.146 0.250 0.175 0.269 0.175
Min. 0.045 0.039 0.052 0.045 0.062 0.052 0.062 0.057 0.078 0.062 0.078 0.069 0.104 0.078 0.104 0.089 0.125 0.089 0.139 0.104 0.156 0.104 0.179 0.125 0.192 0.125
Max. 0.080 0.070 0.094 0.080 0.112 0.094 0.112 0.102 0.141 0.112 0.141 0.125 0.188 0.141 0.188 0.161 0.225 0.161 0.250 0.188 0.281 0.188 0.321 0.225 0.346 0.225
Min. 0.062 0.055 0.073 0.062 0.088 0.073 0.088 0.080 0.109 0.088 0.109 0.097 0.146 0.109 0.146 0.125 0.175 0.125 0.194 0.146 0.219 0.146 0.250 0.175 0.269 0.175
Max. 0.0860 0.0860 0.0990 0.0990 0.1120 0.1120 0.1250 0.1250 0.1380 0.1380 0.1640 0.1640 0.1900 0.1900 0.2160 0.2160 0.2500 0.2500 0.3125 0.3125 0.3750 0.3750 0.4375 0.4375 0.5000 0.5000
Min. 0.0813 0.0816 0.0938 0.0942 0.1061 0.1068 0.1191 0.1195 0.1312 0.1321 0.1571 0.1577 0.1818 0.1831 0.2078 0.2085 0.2408 0.2425 0.3026 0.3042 0.3643 0.3667 0.4258 0.4281 0.4876 0.4906
2 0.0860 2 0.0860 3 0.0990 3 0.0990 4 0.1120 4 0.1120 5 0.1250 5 0.1250 6 0.1380 6 0.1380 8 0.1640 8 0.1640 10 0.1900 10 0.1900 12 0.2160 12 0.2160 1 ∕ 4 0.2500 1 ∕ 4 0.2500 5 ∕ 16 0.3125 5 ∕ 16 0.3125 3 ∕ 8 0.3750 3 ∕ 8 0.3750 7 ∕ 16 0.4375 7 ∕ 16 0.4375 1 ∕ 2 0.5000 1 ∕ 2 0.5000
56 64 48 56 40 48 40 44 32 40 32 36 24 32 24 28 20 28 18 24 16 24 14 20 13 20
3 ∕ 16 3 ∕ 16 7 ∕ 32 3 ∕ 16 7 ∕ 32 9 ∕ 32 1 ∕ 4 5 ∕ 16 9 ∕ 32 5 ∕ 16 7 ∕ 16 1 ∕ 4 11 ∕ 32 11 ∕ 32 13 ∕ 32 17 ∕ 32 13 ∕ 32 19 ∕ 32 15 ∕ 32 11 ∕ 16 7 ∕ 16
5 ∕ 32
3 ∕ 16 5 ∕ 32 7 ∕ 32 3 ∕ 16
5 ∕ 32
1 ∕ 8
1 ∕ 8
5 ∕ 32 5 ∕ 32 3 ∕ 16 5 ∕ 32 3 ∕ 16 3 ∕ 16
3 ∕ 16 5 ∕ 32 7 ∕ 32 3 ∕ 16 7 ∕ 32 3 ∕ 16
1 ∕ 4
7 ∕ 32
1 ∕ 4 1 ∕ 4
1 ∕ 4
5 ∕ 16
1 ∕ 4
3 ∕ 16
1 ∕ 4
7 ∕ 32
1 ∕ 4
5 ∕ 16 9 ∕ 32
1 ∕ 4
7 ∕ 32 5 ∕ 16 5 ∕ 16 9 ∕ 32 1 ∕ 4 9 ∕ 32 7 ∕ 16 5 ∕ 16 5 ∕ 16 9 ∕ 16 3 ∕ 8 15 ∕ 32
7 ∕ 32
13 ∕ 32
11 ∕ 32
5 ∕ 16
1 ∕ 4
13 ∕ 32
11 ∕ 32
3 ∕ 8 1 ∕ 2 3 ∕ 8
5 ∕ 16
13 ∕ 32
5 ∕ 16
9 ∕ 16
15 ∕ 32 11 ∕ 32 11 ∕ 32 19 ∕ 32 13 ∕ 32 1 ∕ 2
15 ∕ 32
5 ∕ 8 1 ∕ 2
1 ∕ 2 3 ∕ 4
23 ∕ 32 17 ∕ 32
9 ∕ 16
3 ∕ 8
25 ∕ 32
19 ∕ 32
3 ∕ 4
5 ∕ 8
9 ∕ 16
3 ∕ 8
17 ∕ 32
13 ∕ 32
a Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place shall be omitted. b The tabulated values apply to screw blanks before roll threading. c Screws of these nominal lengths and shorter shall have point taper length specified above for short screws. Longer lengths shall have point taper length specified for long screws. All dimensions are in inches. See Table 1 for thread diagrams. Type C is not recommended for new designs. Tapered threads shall have unfinished crests.
Made with FlippingBook - Share PDF online