Table 7. ANSI Standard Thread and Point Dimensions for Types D, F, G, and T Thread Cutting Tapping Screws ANSI/ASME B18.6.3-2013
D
P
S
L
Nominal Size a or Basic Screw Diameter 2 0.0860 2 0.0860 3 0.0990 3 0.0990 4 0.1120 4 0.1120 5 0.1250 5 0.1250 6 0.1380 6 0.1380 8 0.1640 8 0.1640 10 0.1900 10 0.1900 12 0.2160 12 0.2160 1 ∕ 4 0.2500 1 ∕ 4 0.2500 5 ∕ 16 0.3125 5 ∕ 16 0.3125 3 ∕ 8 0.3750 3 ∕ 8 0.3750 7 ∕ 16 0.4375 7 ∕ 16 0.4375 1 ∕ 2 0.5000 1 ∕ 2 0.5000
Point Taper Length c
Major Diameter
Point Diameter b
Determinant Lengths for Point Taper c
Minimum Practical Nominal Screw Lengths
For Short Screws
For Long Screws
Threads per inch
Max. 0.068 0.070 0.078 0.081 0.087 0.091 0.100 0.102 0.107 0.113 0.132 0.136 0.148 0.158 0.174 0.180 0.200 0.214 0.257 0.271 0.312 0.333 0.366 0.387 0.423 0.450
Min.
Max. 0.062 0.055 0.073 0.062 0.088 0.073 0.088 0.080 0.109 0.088 0.109 0.097 0.146 0.109 0.146 0.125 0.175 0.125 0.194 0.146 0.219 0.146 0.250 0.175 0.269 0.175
Min. 0.045 0.039 0.052 0.045 0.062 0.052 0.062 0.057 0.078 0.062 0.078 0.069 0.104 0.078 0.104 0.089 0.125 0.089 0.139 0.104 0.156 0.104 0.179 0.125 0.192 0.125
Max. 0.080 0.070 0.094 0.080 0.112 0.094 0.112 0.102 0.141 0.112 0.141 0.125 0.188 0.141 0.188 0.161 0.225 0.161 0.250 0.188 0.281 0.188 0.321 0.225 0.346 0.225
Min. 0.062 0.055 0.073 0.062 0.088 0.073 0.088 0.080 0.109 0.088 0.109 0.097 0.146 0.109 0.146 0.125 0.175 0.125 0.194 0.146 0.219 0.146 0.250 0.175 0.269 0.175
90 ° Heads Csk Heads 90 ° Heads Csk Heads
Max.
Min.
56 64 48 56 40 48 40 44 32 40 32 36 24 32 24 28 20 28 18 24 16 24 14 20 13 20
0.0860 0.0860 0.0990 0.0990 0.1120 0.1120 0.1250 0.1250 0.1380 0.1380 0.1640 0.1640 0.1900 0.1900 0.2160 0.2160 0.2500 0.2500 0.3125 0.3125 0.3750 0.3750 0.4375 0.4375 0.5000 0.5000
0.0813 0.0816 0.0938 0.0942 0.1061 0.1068 0.1191 0.1195 0.1312 0.1321 0.1571 0.1577 0.1818 0.1831 0.2078 0.2085 0.2408 0.2425 0.3026 0.3042 0.3643 0.3667 0.4258 0.4281 0.4876 0.4906
0.061 0.064 0.070 0.074 0.078 0.083 0.091 0.094 0.096 0.104 0.122 0.126 0.135 0.148 0.161 0.168 0.184 0.202 0.239 0.257 0.293 0.319 0.344 0.371 0.399 0.433
3 ∕ 16 3 ∕ 16 7 ∕ 32 3 ∕ 16 7 ∕ 32 9 ∕ 32 1 ∕ 4 5 ∕ 16 9 ∕ 32 1 ∕ 4
5 ∕ 32
3 ∕ 16 5 ∕ 32 7 ∕ 32 3 ∕ 16
5 ∕ 32
1 ∕ 8
1 ∕ 8
5 ∕ 32 5 ∕ 32 3 ∕ 16 5 ∕ 32 3 ∕ 16 3 ∕ 16
3 ∕ 16 5 ∕ 32 7 ∕ 32 3 ∕ 16 7 ∕ 32 3 ∕ 16
1 ∕ 4
7 ∕ 32
1 ∕ 4 1 ∕ 4
1 ∕ 4
5 ∕ 16
1 ∕ 4
3 ∕ 16
1 ∕ 4
7 ∕ 32
11 ∕ 32 5 ∕ 16 7 ∕ 16 11 ∕ 32 7 ∕ 16 13 ∕ 32 17 ∕ 32 13 ∕ 32 19 ∕ 32 15 ∕ 32 11 ∕ 16
1 ∕ 4
5 ∕ 16 9 ∕ 32
1 ∕ 4
7 ∕ 32 5 ∕ 16 5 ∕ 16 9 ∕ 32 1 ∕ 4 9 ∕ 32 7 ∕ 16 5 ∕ 16 3 ∕ 8
7 ∕ 32 11 ∕ 32 11 ∕ 32 5 ∕ 16 13 ∕ 32 5 ∕ 16 1 ∕ 4 15 ∕ 32 11 ∕ 32 11 ∕ 32 19 ∕ 32 13 ∕ 32 1 ∕ 2
13 ∕ 32 5 ∕ 16 13 ∕ 32
3 ∕ 8 1 ∕ 2 3 ∕ 8
9 ∕ 16 15 ∕ 32
15 ∕ 32 5 ∕ 16 9 ∕ 16
5 ∕ 8 1 ∕ 2
1 ∕ 2 3 ∕ 4
23 ∕ 32 17 ∕ 32
9 ∕ 16 25 ∕ 32 9 ∕ 16
3 ∕ 8
19 ∕ 32
3 ∕ 4
5 ∕ 8
3 ∕ 8
17 ∕ 32
13 ∕ 32
a Where specifying nominal size in decimals, zeros preceding decimal and in the fourth decimal place shall be omitted. b The tabulated values apply to screw blanks before roll threading. c Screws of these nominal lengths and shorter shall have point taper length specified above for short screws. Longer lengths shall have point taper length specified for long screws. All dimensions are in inches. See Table 2 for thread diagrams.
“Type D” otherwise designated “Type 1.” “Type T” otherwise designated “Type 23.”
Made with FlippingBook - Share PDF online