Machinery's Handbook, 31st Edition
1054 Files and Burs parallel flat, square, pillar, pillar narrow, half-round and shell types. A special curved- tooth file is available with teeth divided by long angular serrations. The teeth are cut in an “off center” arc. When moved across the work toward one edge of the file a fast cutting action is provided; when moved toward the other edge, a smoothing action; thus the file is made to serve a dual purpose. Swiss Pattern Files: These are used by tool and die makers, model makers and delicate instrument parts finishers. They are made to closer tolerances than the conventional American pattern files although with similar cross sections. The points of the Swiss pattern files are smaller, the tapers are longer, and they are available in much finer cuts. They are primarily finishing tools for removing burrs left from previous finishing operations truing up narrow grooves, notches and keyways, cleaning out corners and smoothing small parts. For very fine work, round- and square-handled needle files, available in numerous cross-sectional shapes in overall lengths from 4 to 7 3 ⁄ 4 inches, are used. Die sinkers use die sinkers’ files and die sinkers’ rifflers. The files, also made in many different cross-sectional shapes, are 3 1 ⁄ 2 inches in length and are available in the cut Nos. 0, 1, 2, and 4. The rifflers are from 5 1 ⁄ 2 to 6 3 ⁄ 4 inches long, have cutting surfaces on either end, and come in numerous cross-sectional shapes in cut Nos. 0, 2, 3, 4 and 6. These rifflers are used by die makers for getting into corners, crevices, holes and contours of intricate dies and molds. Used in the same fashion as die sinkers’ rifflers, silversmiths’ rifflers, that have a much heavier cross section, are available in lengths from 6 7 ⁄ 8 to 8 inches and in cut Nos. 0, 1, 2, and 3. Blunt machine files in cut Nos. 00, 0, and 2 for use in ordinary and bench filing machines are available in many different cross-sectional shapes, in lengths from 3 to 8 inches. Rasps: Rasps are employed for work on relatively soft substances such as wood, leather, and lead where fast removal or material is required. They come in rectangular and half round cross sections, the latter with and without a sharp edge. Special Purpose Files: Falling under one of the preceding five classes of files, but modi fied to meet the requirements of some particular function, are a number of special-purpose files. The long-angle lathe file is used for filing work that is rotating in a lathe. The long tooth angle provides a clean shear, eliminates drag or tear and is self-clearing. This file has safe or uncut edges to protect shoulders of the work which are not to be filed. The foundry file has especially sturdy teeth with heavy-set edges for the snagging of castings—the removing of fins, sprues, and other projections. The die-casting file has extra-strong teeth on corners and edges as well as sides for working on die castings of magnesium, zinc, or aluminum alloys. A special file for stainless steel is designed to stand up under the abrasive action of stainless steel alloys. Aluminum rasps and files are designed to eliminate clog ging. A special tooth construction is used in one type of aluminum tile which breaks up the filings, allows the file to clear itself and overcomes chatter. A brass file is designed so that with a little pressure the sharp, high-cut teeth bite deep, while, with less pressure, their short uncut angle produces a smoothing effect. The lead float has coarse, single-cut teeth at almost right angles to the file axis. These shear away the metal under ordinary pressure and produce a smoothing effect under light pressure. The shear-tooth file has a coarse single cut with a long angle for soft metals or alloys, plastics, hard rubber and wood. Chainsaw files are designed to sharpen all types of chainsaw teeth. These files come in round, rectangular, square and diamond-shaped sections. The round- and square-sectioned files have either double- or single-cut teeth, the rectangular files have single-cut teeth, and the diamond-shaped files have double-cut teeth. Effectiveness of Rotary Files and Burs.— There it very little difference in the efficiency of rotary files or burs when used in electric tools and when used in air tools, provided the speeds have been reasonably well selected. Flexible-shaft and other machines used as a source of power for these tools have a limited number of speeds which govern the revolu tions per minute at which the tools can be operated.
Copyright 2020, Industrial Press, Inc.
ebooks.industrialpress.com
Made with FlippingBook - Share PDF online