Roller Skate Wheel Bump Stops Poly bump stops are 1" tall with a 5/8" diameter hole. ALL64510 ..... 50 Durometer ALL64511 ..... 55 Durometer ALL64512 ..... 60 Durometer ALL64514 ..... 70 Durometer Adjustable Poly Bump Stop Kit ALL64505 Polyurethane bump stop is weather resistant and easily adjustable by adding packers to the inner ring. Five 1/16" thick packer shims included in the kit.
Shock Shims Uniquely designed shock shims are placed directly onto the shock shaft to simplify fine tuning of the chassis without disassembling the shock or even removing the shock from the chassis. Kits include a variety of shim designs and sizes for convenient tuning and set-up. Size Starter Kit Standard Kit
NEW!
ALL64404
NEW!
Deluxe Kit
14mm ALL64400 16mm ALL64440
ALL64402 ALL64442
ALL64404 ALL64444
Starter Kit Includes: U-Shaped Shims 1/16" (4 pcs), 1/8" (4 pcs) and 3/8" (2 pcs); Semi-Solid Shims 1/16" (4 pcs) and 1/8" (4 pcs). Standard Kit Includes: U-Shaped Shims 1/16" (12 pcs), 1/8" (12 pcs) and 3/8" (6 pcs); Semi-Solid Shims 1/16" (12 pcs) and 1/8" (12 pcs); 2-Piece Collar Shims 1/2" (2 pcs), 3/4" (2 pcs) and 1" (2 pcs); Storage Case. Deluxe Kit Includes: U-Shaped Shims 1/16" (12 pcs), 1/8" (24 pcs) and 3/8" (10 pcs); Semi-Solid Shims 1/16" (12 pcs) and 1/8" (24 pcs); 2-Piece Collar Shims 1/2" (6 pcs), 3/4" (6 pcs) and 1" (6 pcs); Storage Case.
Shock Bump Rubbers Conical bump rubbers fit on most shock shafts up to 16mm to limit shock travel. Bump rub- bers are 2-3/8" tall and have a 2" O.D. base. A letter designation is molded in the bottom to identify compound. ALL64500..... Soft (40 grams) ALL64501..... Medium (50 grams) ALL64502..... Hard (55 grams)
Shock Shim Components U-Shaped Shims - Designed for quick removal and installation into tight stacks and locations where twisting the shim into the stack is not an option or when the car is on the ground. Commonly used for fine tuning the suspension. Semi-Solid Shims - Designed for quick removal, providing a secure installation that will not fall out yet requires 3/4" of space to install or remove. Typically installed when the vehicle is off the ground. Commonly used for fine tuning the suspension. 2-Piece Collar Shims - Designed to attach around the shaft of the shock and secure in place with a zip tie. Commonly used during initial set-up or to take up a large amount of travel. Description
Bump Spring Cups Lightweight bump spring
cups are made from 6061-T6 aluminum and have a black anodized finish. Cups feature a bronze bushing, allowing the shock shaft to move freely during suspension travel. Cups have a 2" O.D.
ALL64412
sized for Hypercoil and most Landrum bump springs. Two are required and should closely match bump spring I.D. size to appropriate bump spring cup step O.D. size from chart. Sold each.
ALL64416
Cup Step OD “B”
Shaft Sz. “A”
1.160"
1.200"
1.280"
ALL64420
14mm ALL64348
ALL64349 ALL64353 ALL64357
ALL64350 ALL64354 ALL64358
1/2"
ALL64352 ALL64356
2-Pack 10-Pack 25-Pack
16mm, 5/8"
14mm (.550")
U-Shaped Shim 1/16" U-Shaped Shim 1/8" U-Shaped Shim 3/8" Semi-Solid Shim 1/16" Semi-Solid Shim 1/8"
– – – – –
ALL64410 ALL64410-25 ALL64412 ALL64412-25 ALL64414 ALL64414-25 ALL64416 ALL64416-25 ALL64418 ALL64418-25
2-Piece Collar Shim Kit 1/2" ALL64420 ALL64420-10 2-Piece Collar Shim Kit 3/4" ALL64422 ALL64422-10 2-Piece Collar Shim Kit 1" ALL64424 ALL64424-10
– – –
16mm (.630")
U-Shaped Shim 1/16" U-Shaped Shim 1/8" U-Shaped Shim 3/8" Semi-Solid Shim 1/16" Semi-Solid Shim 1/8"
– – – – –
ALL64450 ALL64450-25 ALL64452 ALL64452-25 ALL64454 ALL64454-25 ALL64456 ALL64456-25 ALL64458 ALL64458-25
2-Piece Collar Shim Kit 1/2" ALL64460 ALL64460-10 2-Piece Collar Shim Kit 3/4" ALL64462 ALL64462-10 2-Piece Collar Shim Kit 1" ALL64464 ALL64464-10
– – –
Billy Moyer, Jr.
Photo: Marcus Berglund
www.allstarperformance.com
197
Made with FlippingBook flipbook maker