Shock Protectors Plastic shock protectors slide over alu- minum threaded body shock to protect against wear from spring. Protector
Spring Pre-Loader Pre-loader allows use of a softer spring rate that is “pre-loaded” at ride height. The pre- loaded spring will have less rate increase as the suspension travels. For example, a 150 lb./in. spring can be pre-loaded to 400 lbs. at ride height, but still only increases at a rate of 150 lb./in. as suspension travels. The entire
measures 6" from spring seat to end, has an I.D. that measures 2-1/4" and works with all 2-1/2" I.D. springs. Unit should just cover shock body and may need to be cut to specific length.
unit may also be exchanged with another unit with a different rate spring pre-installed to allow spring rate changes without affecting ride
ALL64200..... Blue ALL64201..... Black
height. Commonly used on the rear coil-overs, pre-loader requires 3" I.D. spring, includes a thrust bearing set and fits most shocks. Note: Unit is typically installed with slotted inner half towards the shock body. Always check
Shock Protectors Shock Protectors add extra protection from rocks and debris to your shock body. Plastic protector simply snaps onto your shock body. May need to be cut to length. Sold each.
components for possible interference. ALL64230..... Pre-Loader For 10" Tall Spring ALL64232..... Pre-Loader For 12" Tall Spring ALL64234..... Pre-Loader For 14" Tall Spring ALL64212 ..... Replacement 3" Bearing Set Related Parts ALL11187 ...... Pre-Loader Body Wrench ALL11188...... Pre-Loader Nut Wrench Thrust Bearing Kits Bearing kits are placed between the coil spring and the adjuster nut to reduce friction when making adjust- ments. Kits are recommended for
ALL64202..... 2" Standard Body Shocks ALL64203..... 1-5/8" Small Body Shocks
ALL11187
Shock Shaft Boot ALL64198 Rubber bellows style boot is 10" long, one end has an 1-1/4" opening while the other is 2". Boot fits most non-coil-over shocks.
ALL11188
Shock And Pull Bar Covers Neoprene covers help protect from rock damage and to keep components clean while preventing the competition from knowing your secrets. Hook-and-loop material allows easy cover removal for adjustments. 3" covers are often used for 2-1/2" and 3" coil-over shocks and small diameter upper links. 6" covers work well on 5" springs and pull bar applications.
preloaded spring assemblies or when springs require adjustment while they are under pressure. Kits include one bearing and two races.
ALL64210 ..... 2.5" Kit (2.5" I.D. x 3.25" O.D.) ALL64212 ..... 3" Kit (3.025" I.D. x 3.730" O.D.) ALL64214 ..... 5" Kit (4.150" I.D. x 5.045" O.D.)
ALL64204..... 3" x 14" ALL64205..... 3" x 16" ALL64206..... 6" x 7" ALL64207..... 6" x 14" ALL64208..... 6" x 16" ALL64209..... 6" x 20"
Hydraulic 2-1/2" Coil-Over Spring Adjuster ALL64220 Weight jack assembly allows driver to adjust car handling while driving. Turning the adjustment knob will extend spring cup up to 7/8" to increase or decrease spring pressure. Assembly includes hydraulic ram,
Coil-Over Eliminator ALL64100
hydraulic pump with adjustment knob, 9' braided hose, and two washers for use with standard or threaded body shocks. Black anodized finish. Replacement Part ALL64222..... O-Ring Kit For ALL64220
Eliminator fits conventional 5" coil springs. Adjuster locks spring into place. Kit includes a threaded shaft, two spring plates, one adjuster, two rod ends and two jam nuts. Easily adjusted with ALL11146 wrench. Not to be used as a suspension limiting device, check maximum travel before use.
www.allstarperformance.com
199
Made with FlippingBook flipbook maker