Clamp-On Shock Brackets Clamp-on shock brackets mount standard and coil- over shocks with 1/2" I.D. inner bushings to round
Steel Shock Quick Pin ALL60108 Steel shock quick pins allow coil-over shocks to be quickly serviced or changed. Works with Allstar coil-over brackets, eliminating the need for a separate bushing. Shock quick pins are 2-1/2" long and include a hairpin. Sold each. Titanium Shock Quick Pins Titanium shock quick pins allow coil-over shocks to be quickly serviced or changed. ALL17120 has a long shoulder and will work with Allstar coil-over brackets, eliminating the need for a separate bushing. ALL17121 is commonly used on non-bushing type brackets, but can be used with Allstar brackets along with bushing. Shock quick pins are 2-1/2" long and include a hairpin. ALL17120...... Quick Pin With Shoulder ALL17121...... Quick Pin Without Shoulder
tubing without welding. Easily add additional mount or pivot mount when experimenting or trying different set-ups. Standard brackets
position the shock approximately 1" below the chassis tubing. Drop mount brackets position the shock approxi- mately 2-1/2" below the chassis tubing. Brackets include mounting hardware with nyloc locking nuts. Clamp-On Drop Mount Clamp-On ALL60220..... 1-3/4" ALL60224 ............ 1-3/4" ALL60221 ..... 1-1/2" ALL60225............ 1-1/2" ALL60222..... 1-1/4" Upper Coil-Over Shock Mount Kit ALL60230
ALL17120
ALL17121
Weld-in kit provides a mounting point for rear coil-over shock mounts in tube, boxed or stock frames with up to 48" between frame rails. Great for drag racing and street
Quick Release T-Handle Pins
Positive lock quick release pins hold tightly in place until the handle button is depressed, allowing the pin to be inserted
Lengths stated are from base of T-handle to top of detent ball.
applications, kit includes a 48" long, .120" wall x 1-1/2" mild steel tube, reinforced mounting tabs, 2" x 3" end plates and 1/2" hardware. 1/2" Rod End Mount ALL60073 3/16" thick steel mount with 1/2" holes accepts rod ends up to 5/8" wide. Mount is 1-5/8" tall overall. Track Bar Locator Brackets Track bar locator brackets are an ideal bolt-on mounting point for rod ends commonly found on Panhard bars, track bars or rear axle housing track locators. For use with 1/2" diameter rod ends. Available with a 5/8" or 3/4" bracket mounting hole. ALL60079..... 5/8" Hole, 1" Gap ALL60089..... 3/4" Hole, 1-3/16" Gap
or removed into or out of a hole with ease. Handles are made from 380 die cast aluminum, shanks are made from 4130 steel. Each pin is equipped with a stainless steel split ring, allowing the option to attach a cable assembly. ALL60300..... 1/4" x 1" ALL60314..... 3/8" x 3" ALL60301..... 1/4" x 1-1/2" ALL60318..... 1/2" x 2" ALL60302..... 1/4" x 2" ALL60320..... 1/2" x 2-1/2" ALL60304..... 5/16" x 1" ALL60322..... 1/2" x 3" ALL60306..... 5/16" x 2" ALL60324..... 1/2" x 3-1/2" ALL60308..... 5/16" x 3" ALL60326..... 5/8" x 2" ALL60310 ..... 3/8" x 1" ALL60328..... 5/8" x 2-1/2" ALL60312 ..... 3/8" x 2" ALL60330 .... 5/8" x 3"
Quick Pin Lock Collar Steel lock collar provides a
Smart Tool ALL10113 Ensure that chassis tubing is level and plumb when building roll cages or checking driveshaft
positive lock for quick release pins. Black coated collar with button head machine screw allows attachment of a securing device, like an Allstar lanyard (ALL18461 or ALL18463).
ALL60335
angles. Also works on trailing arms and suspension tubes when used with ALL10740 Smart Tool Tray. A “hold” button freezes and unfreezes readings which can be displayed as degrees, percentages, or in./ft. at the push of a button. Plus and minus signs indicate when pitch is more or less than that shown on the display. Pitch reads in 1/8 in./ft. increments. Level emits a “beep” at level and plumb. The tool shuts off automatically if idle for more than six minutes. Powered by a standard 9 volt battery.
ALL60335..... 1/2" Collar With 10-32 Screw ALL60336..... 5/8" Collar With 1/4"-28 Screw
www.allstarperformance.com
201
Made with FlippingBook flipbook maker