2-Piece Limit Chain Clamps 2-Piece clamp bolts around most 3" O.D. axle tubes providing a lower mounting point for a suspension limit chain. Two piece design features a nylon liner allowing clamp to be installed without removing existing brake brackets and hubs. ALL68336..... Steel ALL68337..... Aluminum 1-Piece
Coil-Over Load Bolt Assembly ALL56074 Threaded aluminum bolt is 6" long with 1-1/8"-12 fine threads and is commonly used as an adjust- able travel limiter. Also used with ALL56098 threaded sleeve. ALL56075..... Replacement Shock End Suspension Limiter Single bushing suspension limiter is com- monly used on the chassis LR or RR to limit travel during acceleration “hike up” and control roll steer. Dual bushing limiter is often used on the lift bar to control lift bar travel on deceleration. Bushing design reduces or absorbs shock when suspension is limited and helps reduce tire unloading. Top plate is drilled to attach a 1/2" rod end when used in a shock mount or for attaching to a weight jack bolt with 7/16"-20 internal threads using optional chrome moly stud ALL64304. Clevis has a 3/8" hole for simple attachment to a chain or cable.
Limit Chain Clamps 1-Piece bearing style clamp slides over the end of most 3" O.D. axle tubes providing a lower mounting point for a suspension limit chain. ALL68332..... Steel ALL68333..... Aluminum
Retainer Clamps, 2-Piece Retainer clamp bolts around most 3" O.D. axle tubes to keep bird cages, floater
ALL64300..... Single Bushing Limiter ALL64302..... Dual Bushing Limiter ALL64304..... Chrome Moly Stud With Jam Nut
brackets, limit chain clamps in position. 2-piece design allows clamp to be installed without removing existing brake bracket and hub. ALL68338..... Steel ALL68339..... Aluminum Retainer Clamps, 1-Piece Steel retainer clamp slides over the end of most 3" O.D. axle tubes to keep bird cages, floater brackets, and limit chain clamps in position. Powder coated black finish. Lightweight
Limiter Chain Kit Commonly used to limit rear
suspension or lift bar travel. Chain can be easily cut to required length. Shrink sleeve installs over chain, and
when heated with a heat gun, shrinks to keep chain in position and prevent chain from binding or catching on itself. ALL64312 ..... 3/16" Diameter Accepts 3/8" Pin or Bolt ALL64314 ..... 5/16" Diameter Accepts 1/2" Pin or Bolt
Heavy Duty
Mounting Hardware
Part No. Description Width Thickness
ALL68326 Lightweight ALL68328 Lightweight
1/2" 5/8"
1/8" 1/8" 1/4"
1/4" 3/8" 3/8"
QC Axle Tube Support Brackets Brackets provide mounting points for a strut rod assembly to help eliminate flex found in quick change
ALL68327 Heavy Duty 5/8"
Clamp-On Rings Steel brackets bolt to 3" axle tubes. Choose from five widths in 1-, 2- and 4-bolt designs.
ALL68320
ALL60143 ..... 1-Bolt, 5/8" Wide ALL60144..... 2-Bolt, 1" Wide ALL60145 ..... 2-Bolt, 1-3/4" Wide ALL60146 ..... 2-Bolt, 2" Wide ALL60147 ..... 4-Bolt, 3" Wide
ALL68322
ALL60143
rear ends. ALL68320 attaches to the side bell bolts on most quick change rear ends. ALL68322 has tabs with 1/2" holes and mounts directly onto a 3" axle tube. ALL68320..... Center Section Mount ALL68322..... Axle Tube Mount
Suspension Tubes See Page 200
ALL60145
Axle Tube Bracket ALL68324 Bracket clamps around 3" wide axle tubes to provide a mounting point for a suspen- sion limiter such as a limiting strap or chain. 1" wide bracket has tabs with 1/2" holes.
ALL68320 ALL68322
www.allstarperformance.com
213
Made with FlippingBook flipbook maker