Cleco Pin Fastener Kits Cleco pins are reusable and easily make a temporary connec-
Quick Turn Spring Fixture Accurately drill panels when installing quick turn fastener springs. Start with a 1/4" center hole and use the fixture to locate and drill 1/8" holes for mounting the springs. Size listed is spring center-to-center distance.
ALL19407
tion between pieces of sheet metal during fit- ting. Pins will work with
thicknesses up to 1/4", kits include pliers and 10 pins. ALL18221 ..... Kit With 1/8" Pins ALL18225 ..... Kit With 3/16" Pins Cleco Pliers ALL18220
ALL19406 ..... Fixture For 3/4" Spring ALL19407 ..... Fixture For 1" Spring ALL19408 ..... Fixture For 1-3/8" Spring Spindle Checker Tools Assure correct alignment of the
Unique tool readily installs and removes Cleco fasteners.
upper and lower ball joint when checking for bent spindles. Insert slugs
into spindle and guide rod will fit
Pin Type Cleco Fasteners Cleco pins permit quick, easy installation and removal of sheet metal during fitting. Pins work with thicknesses up to 1/4". 1/8" Dia. Pins 3/16" Dia. Pins ALL18222 ..... 10-Pack
through slugs if spindle isn’t bent. Kits fit most aftermarket race and GM stock Metric spindles. ALL11176 ...... Kit With GM Lower, 2" Taper ALL11177 ...... Kit With Chrysler Lower, 1-1/2" Taper ALL11184...... Kit For GM Metric, 2" Taper Related Parts ALL99140..... GM Lower Slug With Nut (2" Per Ft.) ALL99141 ..... Chrysler Lower Slug With Nut (1-1/2" Per Ft.) ALL99158 ..... GM Metric Lower Slug With Nut (2" Per Ft.) ALL99142 ..... Upper Slug With Nut (1-1/2" Per Ft.) ALL99159 ..... GM Metric Upper Slug With Nut (2" Per Ft.) ALL99143 ..... Replacement Guide Rod Taper Reamers Repair or enlarge tapered holes to accept tie rod ends or ball joints. Reamers may be used in a drill with a 1/2" chuck by removing the T-handle.
ALL18226 ...... 10-Pack ALL18227 ...... 25-Pack ALL18228...... 100-Pack
ALL18223 ..... 25-Pack ALL18224 ..... 100-Pack
TECH TIP Drill holes one drill size smaller than the Cleco pin size to assure a tight fit.
Clamp Type Cleco Fastener ALL18230
Use when drilling is not an option. Smooth throat prevents paint damage, and spring exerts strong clamping pressure. Throat depth is 1" with a maximum clamping range of 1/2".
ALL11170 ...... Reamer, 7.15°, 1-1/2" Taper Per Ft. ALL11172 ...... Reamer, 9.56°, 2" Taper Per Ft.
Quick Turn Fastener Wrench ALL19400 The Allstar quick turn fastener wrench fits slot head fasteners and
Taper Reamer Specifications For Ball Joints Part No. Taper Specs Part No.
Taper Specs
Ball Joint
Ball Joint ALL56217 ALL56218 ALL56220 ALL56280 ALL56284 ALL56286
ALL56204 1-1/2" Per Ft.
1-1/2" Per Ft.
ALL56206 ALL56208
2" Per Ft. 2" Per Ft.
2" Per Ft. 2" Per Ft.
reduces the risk of body panel or fastener damage when using screwdrivers for loosening or tightening. Features a non-slip handle. Quick Turn Spring Adjuster ALL19405 This tool is a must when adjusting tension of quick turn springs. Simply turn knob on adjuster to evenly pull or push spring without kinking or breaking spring. Transfer Punches Used to mark quick turn fastener locations, place transfer punch in the initial hole in weld plate or body panel. Position the panel to be marked over top of punch and lightly tap with a hammer.
ALL56210 1-1/2" Per Ft.
1-1/2" Per Ft. 1-1/2" Per Ft. 1-1/2" Per Ft.
ALL56212
2" Per Ft.
ALL56214 1-1/2" Per Ft. ALL56216 1-1/2" Per Ft.
–
–
Ball Joint Spreader Tool ALL11174 Tool separates ball joint from the spindle. Inside of cylinder is shaped to fit over tapered stud of most ball joints and presses against stud of other ball joint. Not for use on FWD or 4WD applications. Tool is 4" tall fully collapsed and 6" tall fully extended. Related Part ALL11175 ...... 1" Extensions (Set of two) ALL11175
ALL19402 ..... For 5/16" Fasteners ALL19403 ..... For 7/16" Fasteners
www.allstarperformance.com
221
Made with FlippingBook flipbook maker