Engine Lift Plate ALL10123 Ease engine swaps with the Allstar engine lift plate. Bolts to manifold in place of carburetor. Yellow zinc coated plate fits standard Holley 4150/4160 and
Freeze Plug Driver Set ALL96482 Have problems installing freeze plugs? Use these plastic drivers along with a hammer or mallet for simple instal-
lation without damaging the plugs or the block. Three sizes per set: 1-1/2", 1-5/8", 1-3/4". (Size refers to size of plug) Individual Drivers
4500 Dominator, Rochester Quadrajet, Carter, Motorcraft, Edelbrock, Edelbrock Q-Jet and Carter AFB carburetors.
All-In-One Engine Lift Plate ALL10137 Engine Plate has provi- sions to fit all LS GM engine blocks and most Holley 4150/4160 and 4500 series, Rochester Quadrajet, Edelbrock and Carter AFB Carburetors. Plate features three lifting points for various chain positioning which allows engine weight to be balanced or offset. An offset position is especially helpful when angling an engine (with transmission attached) in or out of a vehicle. Constructed of 3/16" thick zinc plated steel. NEW!
ALL96483 .... 1-1/2" Driver ALL96484 .... 1-5/8" Driver ALL96485 .... 1-3/4" Driver Cam Bearing Installation Tool ALL96470
For installing cam bearings quickly and easily without damage. Shaft is steel; pilot and driver are aluminum.
LS Main Cap Removal Tool ALL96525 Quickly and easily pull main bearing caps off GM LS series V8
Engine Lift Plates For LS Series GM Engines
Engine plates are designed for lifting LS series GM engines. Installation of lift plate requires removal of the intake mani-
engines, especially those with main studs. Hook tool to the bottom of cap, press down on handles, and the bal- anced leverage pulls the cap out of the block with one swift motion. 26" long x 4" high.
fold and valley cover tray to properly secure lift plate to engine block. Plate features three lifting points, allowing engine weight to be balanced or offset. Made from 3/16" thick zinc plated steel. ALL10140 ..... LS Gen III Engine Lift Plate ALL10143...... LS Gen IV Engine Lift Plate ALL10141...... LS Gen V Engines Ford EFI Engine Lift Plate ALL10125 Ease engine swaps with the Allstar engine lift plate. Fits standard 5.0L/5.8L EFI intakes: OEM, GT-40, Cobra, Holley, Edelbrock.
ALL10140
Rod And Piston Holder ALL96478 Holder safely supports piston and connecting rod assem- blies during engine teardowns or assembly. Slots are 4-3/4" L x 1-1/2" W to accommodate most combinations. Holder mea- sures 24" x 12" x 9-1/2" tall and can be disassembled for storage.
Engine Oil Pressure Primer Tank ALL10535 Primer tank supplies initial oil to the oil pump in engines equipped with a crank driven oil pump. Fill primer tank with
Rod Guide Tool ALL96480 Plastic tool slips over 3/8" or 7/16" rod bolts to aid piston installation and elimi- nate the chance of rod bolts hitting crank. A must for any engine builder’s toolbox. Related Part ALL96481..... Rod Guide Tool Extensions 4.5", 1-Pair Plastigage ® Kit ALL96475 Plastigage strings are a simple and accu- rate way to verify crankshaft, main and rod bearing clearances. Kit includes two green .001" to .003" and one red .002" to .006" (12" long strings), individually packaged inside calibrated sleeves. Detailed instructions are included.
engine oil, then apply compressed air to force the fluid throughout the engine via the oil pressure sender/switch port to pre-lube the entire engine including the oil pump.
Oil Filter Cutter ALL10538
Tool removes the outer shell of most spin-on style engine oil filters to inspect the filter material for contamination or debris.
www.allstarperformance.com
226
Made with FlippingBook flipbook maker