Torque Ball Safety Blanket ALL55220 Fire resistant safety blanket designed by Jason Meyers Racing protects drivers’ legs and feet in the event of a U-joint failure. Ballistic nylon covered blanket weighs just 1-1/2 lbs. and has quick release adjustable straps that allow blanket to be removed easily for servicing torque ball and U-joint. Blanket includes two mounting brackets, mounting studs, nuts and
Bert Clutch Assembly Tool ALL14295 Shaft is used to help align counter shaft when replacing clutch discs and clutches. Shaft features a through hole for installing threaded rod
when assembling counter gear assembly before instal- lation, along with an internal thread to assist when removing if necessary.
installation instructions. Replacement Parts
Tailshaft Seal And Bushing The tailshaft bushing is a regular wear
ALL55224 ..... 3/8" Mounting Stud Kit ALL55226 ..... Mounting Tabs, 1-Pair
item, located inside the transmission tailshaft housing. It should be replaced when replacing the tailshaft seal or when a driveshaft failure has occurred. A worn bushing will cause excessive side-to-side movement of the slip yoke and create a vibration or leak. Replacement bushing and seal fits GM Powerglide, Turbo 350, Saginaw, Muncie, Bert and Brinn transmissions. ALL72150 .... Seal ALL72152 .... Seal With Bushing Slip Yokes Slip yokes provide an important link in today’s driveline and chassis combinations. Yokes are available in standard length for most street applications with minimal suspen- sion travel to extra-long for racing suspensions that have a radical amount of travel. 27-spline yokes accept 1310 style U-joints and are for use in many popular transmissions ALL72152
Bellhousing Dowel Pins Steel dowel pins are approximately 1/2" longer than stock pins and are required when
ALL38152
running an engine mid-plate, rear motor mounts or an aftermarket bellhousing. These extended length pins also help with alignment when installing an engine. Pins fit most GM blocks and are sold in pairs.
ALL38150 ..... Solid Pins ALL38152 ..... Hollow Pins
Solid Transmission Mount ALL38070 Solid 3/16" steel mount fits most TH350,
including TH350, TH700R4, Muncie and Saginaw 3 and 4 speeds, Bert and Brinn
non-ball spline. ALL69040..... 6"
TH400, Powerglide, and all BorgWarner, Muncie, and Chrysler 4-speed transmissions. Eliminates twisting, flex, and distortion. Not recommended for use with rubber engine mounts.
ALL69042..... 6-3/4" ALL69044..... 7-1/2" ALL69046..... 8" ALL69048..... 8" (Extra Clearance) Hardened ALL69043..... 6-3/4" ALL69045..... 7-1/2" ALL69047..... 8" U-Joints Performance U-joints are greasable and fit a variety of driveshaft combinations.
6-3/4"
4-3/4"
Transmission Mount Bracket ALL38072 May be welded to chassis to support manual or automatic transmissions. Steel bracket is 1/8" thick with 1" x 7/16" slots for mounting bolts.
ALL69042 ALL69043
1310 Series: 3.218" Wide with 1.062" Diameter Caps 1330 Series: 3.622" Wide with 1.062" Diameter Caps 1350 Series: 3.622" Wide with 1.187" Diameter Caps U-Joints With Same Cross Width
Clutch Discs For Bert Transmission
Quality discs are a must when rebuilding the internal clutch of Bert transmissions. Friction disc and steel plate sets are sold separately. Note: Friction discs need to be soaked in Type-F automatic transmission fluid for at least 2 hours before installation. ALL26950.....Clutch Friction Discs 6-Pack ALL26952.....Steel Clutches 5-Pack
ALL69030..... 1310 Series ALL69031..... 1330 Series ALL69032..... 1350 Series U-Joints With Different Cross Widths ALL69034..... 1310 to 1330 ALL69037..... 1310 to 1330* ALL69035..... 1310 to 1350 ALL69036..... 1330 to 1350 *Standard 1330 spread with larger 1.125" diameter caps.
Width = B, Caps = A
www.allstarperformance.com
253
Made with FlippingBook flipbook maker