Remote Starter Button Shroud Kits Kit mounts a remote starter button directly to chassis tubing. Kit includes a shroud to help protect against acci- dental activation, tab, and starter button. ALL60360..... Welded Kit ALL60361 ..... Un-welded Kit Battery Boxes
Tubing End Caps Steel end caps weld to the end or inside of tubing to provide a clean look, prevent sharp exposed edges and seal tubes to keep out dirt and debris. Caps are commonly used on ends of bumpers, to fill existing holes in frames and as a flat gusset when butt joining sections of square or rectangular tubing. Package of 10. Part No. Description Thickness Round End Caps ALL22280 7/8" O.D. .125" ALL22285 1" O.D. .125" ALL22281 1-1/4" O.D. .125" ALL22286 1-3/8" O.D. .125" ALL22282 1-1/2" O.D. .125" ALL22283 1-5/8" O.D. .125" ALL22287 1-11/16" O.D. .125" ALL22284 1-3/4" O.D. .125" Square End Caps ALL22290 1" x 1" .085" ALL22291 1-1/2" x 1-1/2" .085" ALL22292 2" x 2" .085" Rectangle End Cap ALL22294 2" x 3" .085" Gussets Gussets add support and strength to tubing joints when building roll cages or chassis mounts. Solid, one or three hole gussets are 1-7/8" tall x 1/8" thick. Description 10-Pack 100-Pack Solid ALL22192 ALL22192-100 With One Hole ALL22194 ALL22194-100 With Three Holes ALL22196 ALL22196-100 Wrap Around Gussets
ALL60361
Universal, lightweight steel bat- tery boxes may be welded or bolted to the frame. Boxes are avail- able in two sizes and include hold down hardware. ALL76100 ..... Full Size, 12" Wide x 7-1/4" Deep ALL76101 ..... Short Style, 10" Wide x 7-1/4" Deep Bolt-On Battery Boxes Battery box has multiple 1/2" mounting holes to bolt box directly to the frame rail, inner fender or firewall. Box can also be fastened to round tubing using clamp-on ballast brackets. Constructed of 13 gauge steel, measures 11" wide x 7" deep and includes 3/8" battery hold down hardware. ALL76102 ..... Clear Zinc ALL76103 ..... Black Stainless Steel Drop-Out Battery Box ALL76105 The perfect battery box where battery mounts under floor. Eases battery service and replacement. Box is 10-1/2" wide, 7" deep, and 9-1/2" tall and will accept most standard batteries. Ground Stud ALL76147 Steel ground stud welds to round tubing providing a secure location for mounting a negative battery cable. Weld stud directly to the chassis or create a secure ground wire location in the foot box or engine compartment. Stud accepts battery cables with 3/8" ring terminals.
ALL76103
Gussets fit 1.50" to 1.75" tubing and can be used to join tubing from 70° to 110°. Wrap around gussets are 1/16" thick and provide more support and rigidity than
a standard flat gusset. . ALL22199 ............ 10-Pack ALL22199-50....... 50-Pack
Rub Rail Flange ALL60023 Flanges are 3/16" thick and commonly used when building bolt-on style rub rails. Center hole accepts 1-1/4" tubing and has two 3/8" mounting holes spaced 2-1/4" apart. Package of 4. Charging Post Bracket ALL60064 Securely mount Allstar charging posts on vehicles where battery is not easily accessible. Predrilled holes allow quick mounting to frame or body. Double-D hole design positions posts close together, but provides enough room for charging or jumper cable clamps. Charging posts sold separately.
Upper Coil-Over Shock Mount Kit ALL60230 Weld-in kit provides a mounting point for rear coil-over shock mounts on tube, boxed or stock frames with up to 48" between frame rails. Great for drag racing
and street applications, kit includes a 48" long, .120" wall x 1-1/2" mild steel tube, reinforced mounting tabs, 2" x 3" end plates and 1/2" hardware.
www.allstarperformance.com
52
Made with FlippingBook flipbook maker