EUROPEAN HAND PROTECTION STANDARDS
EN 16350:2014 Protective Gloves: Electrostatic Properties This European standard specifies a test method for the electrostatic properties of gloves. The test improves on EN1149 as it requires a lower vertical resistance of less than 10⁸ ohms. Gloves tested to EN16350:2014 can be used in areas where there may be an increased risk of explosion, such as in a refinery. IEC 61340-5-1:2016 Protection of Electronic Devices from Electrostatic Phenomena: General Requirements This standard specifies a test method for PPE products used in high sensitive areas where an electrostatic charge can potentially cause damage to delicate components such as electrical circuit boards and microchips. All gloves in the Portwest ESD Glove collection have been tested to both standards.
EN374
Protective Gloves : Against Chemicals And Micro- Organisms EN ISO 374-1:2016 (AS/NZS 2161.10.1) Terminology and performance requirements for chemical risks. New to the standard - There are now 3 standard classes related to the performance level and number of chemicals they protect against. There are 6 additional chemicals to test against. There is a requirement to test for degradation EN 374-4:2013. EN374-3:2003
is withdrawn and is replaced by EN 16523-1:2015. Gloves longer than 400mm will have to be additionally tested in the cuff area. The requirement for testing to EN388 has been removed. The “low chemical” or “Waterproof” beaker symbol has been withdrawn.
ISO 374-1:2016/Type C
ISO 374-1:2016/Type B
ISO 374-1:2016/Type A
EN ISO 10819
Protective Gloves: Mechanical Vibration And Shock EN 10819: 1996 (AS/NZS 2161.3) This European Standard specifies a method for the laboratory measurement, the data analysis and reporting of the vibration transmissibility of gloves in terms of vibration transmission from a handle to the palm of the hand in the frequency range from 31.5 Hz to 1250 Hz. The standard is intended to define a screening test for the vibration transmission through gloves.
X - Low Chemical
XYZ
UVWXYZ
Code Chemical
Class
A Methanol
Primary alcohol
EN 10819
B Acetone
Ketone
C Acetonitrile
Nitrile compound
EN 455:2000 Medical gloves for single use
D Dichloromethane
Chlorinated paraffin
E Carbon disulphide
Sulphur containing organic compound
EN455
Part 1: Requirements and testing for freedom from holes Part 2: Requirements and testing for physical properties Part 3: Requirements and testing for biological evaluation Part 4: Requirements and testing for shelf life determination
F Toluene
Aromatic hydrocarbon
G Diethylamine
Amine
H Tetrahydrofurane
Hetero-cyclic and ether compound
I
Ethyl acetate
Ester
CE foodsafe European legislation with respect to Food Contact Materials (Directive EC1935/2004) requires that food contact materials shall not transfer their ingredients to food and must not modify the organoleptic properties (ie. colour, smell, texture and taste) of the food. Products intended for food contact shall be labelled as such.
J
n-Heptane
Saturated hydrocarbon
K Sodium hydroxide 40%
Inorganic base
L Sulphuric acid 96%
Inorganic Mineral Acid
M 65% Nitric Acid
Inorganic mineral acid, oxidising
N 99% Acetic Acid Organic acid O Ammonia hydroxide 25% Organic acid P 30% Hydrogen peroxide Peroxide S 40% Hydofluoric acid
EN511
Protective Gloves Against Cold EN 511:2006 (AS/NZS 2161.5)
The European Standard EN 511 specifies the requirements and test methods for gloves which protect against conductive cold down to -50 degrees Celsius. This cold can be linked to the climate conditions or an industrial activity.
Inorganic inerla acid, contact poison
i
T 37% Formaldehyde
Aldehyde
3 3 1
EN ISO 374-2:2014 Determination of resistance to penetration There are no major changes from EN374-2:2003
REQUIREMENTS
PERFORMANCE LEVELS 0-1 c: WATER PENETRATION
ISO 374-5:2016
EN374
EN ISO 374-4:2013 Determination of resistance to degradation by chemicals (DR) New to the standard – tests puncture resistance before and after exposure to a challenge chemical. The average of the performance will be recorded in the usersheet as a percentage (%). EN ISO 374-5:2016 Terminology and performance requirements for micro-organisms risks Microorganisms are classed as bacteria, viruses or fungi. Gloves protecting against viruses must also pass ISO16604:2004. EN 16523-1:2015 Determination of material resistance to permeation by chemicals. Permeation by liquid chemical under conditions of continuous contact. This test is similar to EN374-3 therefore gloves certified to EN374-3 do not need to be retested.
PERFORMANCE LEVELS 1-4 b: RESISTANCE TO CONTACT COLD
PERFORMANCE LEVELS 1-4 a: RESISTANCE TO CONVECTIVE COLD
Marking of gloves protecting against, bacteria and fungi
EN381
Protective Gloves : For Users Of Hand Held Chainsaws EN 381-7: 1999 This European Standard specifies the requirements for gloves for resistance to cutting by a chainsaw when assessed by the test method described in EN381-4. The requirements are also given for marking and for the provision of information to be supplied by the manufacturer including criteria for the selection of appropriate gloves and instructions for use.
ISO 374-5:2016
EN374
CLASS 1
Additional marking for Virus
Class
0
1
2
3
Maximum chain speed (m/s)
16m/s
20m/s
24m/s
28m/s
307
Made with FlippingBook Digital Publishing Software