maxon Product Range 2020 / 21

ECX SPEED 19 M brushless BLDC motor ∅ 19 mm Sterilizable, Ceramic Bearings Key Data: 60/92 W, 10.9 mNm, 100000 rpm

 M 1:1

Motor Data Nominal voltage No load speed No load current Nominal speed

1_ 2_ 3_ 4_ 5_ 6_ 7_ 8_ 9_

18 48 64700 64600 64600 63400 247 185 123 90.1 59800 59500 59700 58600 10.9 9.65 9.98 10.2 4.31 2.87 1.97 1.48 179 150 164 169 67.7 42.4 31 23.5 88.4 87.4 87.9 88.1 0.266 0.566 1.16 2.04 0.0234 0.0438 0.0986 0.182 2.64 3.53 5.3 7.2 3610 2700 1800 1330 363 433 396 376 4.38 5.22 4.77 4.53 1.15 1.15 1.15 1.15 16.8 1.6 2.36 696 -40…+135 155 100000 0…0.29 4 24 36 40000 60000 80000 100000 120000 Operating Range n [rpm] winding 36 V

V

rpm mA

rpm Nominal torque (max. continuous torque) mNm Nominal current (max. continuous current) A Stall torque mNm Stall current A Max. efficiency % Terminal resistance W Terminal inductance mH Torque constant mNm/A Speed constant rpm/V Speed/torque gradient rpm/mNm Mechanical time constant ms Rotor inertia gcm 2 Thermal data

10_ 11_ 12_ 13_ 14_ 15_ 16_ 17_ 18_ 19_ 20_ 21_ 22_ 23_ 24_ 25_ 26_ 27_ 28_ 29_ 30_ 31_ 32_

Sterilization information Sterilization cycles Sensorless: typical 2000 Hall sensors: typical 1000 Sterilization with steam Temperature Compression pressure up to

Thermal resistance housing-ambient Thermal resistance winding-housing Thermal time constant winding Thermal time constant motor Ambient temperature Max. winding temperature Mechanical data ball bearings Max. speed

K/W K/W

s s

°C °C

+134°C ±4°C

2.3 bar 100% 18 min.

rpm mm

Rel. humidity Cycle length

Axial play Preload Radial play Direction of force

N

Continuous operation Continuous operation with reduced thermal resistance R th2 50% Short term operation

pull

preloaded

20000

Max. axial load (dynamic) Max. force for press fits (static) (static, shaft supported) Max. radial load [mm from flange]

N N N N

4 70

0

M [mNm]

0

5

10

15

5000 12 [5]

maxon Modular System

Details on catalog page 32

Other specifications Number of pole pairs Number of phases Weight of motor Typical noise level [rpm]

maxon motor control 487_ESCON 36/3 EC 487_ESCON Module 50/4 EC-S 487_ESCON Module 50/5 489_ESCON 50/5 491_DEC Module 50/5 495_EPOS4 Micro 24/5 496_EPOS4 Mod./Comp. 50/5 497_EPOS4 Comp. 24/5 3-axes 501_EPOS4 50/5 504_EPOS2 P 24/5

maxon gear 338_GPX 19 SPEED 343_GPX 22 SPEED

maxon sensor 441_ENX 19 EASY INT 441_ENX 19 EASY INT Abs. for motor type A: for motor type B:

Stages [opt.]

1 3 78 48 [50000]

1–2 [3]

g

dBA

Connection A and B, motor (Cable AWG 20) red Motor winding 1 black Motor winding 2 white Motor winding 3 Connection A, sensors (Cable AWG 26) orange V Hall 3…24 VDC blue GND yellow Hall sensor 1 brown Hall sensor 2 grey Hall sensor 3

Configuration

Flange front: thread holes/center thread Flange back: plastic ring/external thread/with opening Shaft front: length/diameter Electric connection: cable length/pin connection Temperature Sensor: NTC-Thermistor Appropriate connectors and connecting cables are available for the configuration of the pin connection together with the external thread: see catalog, Accessories section.

Wiring diagram for Hall sensors see page 47. In combina- tion with the ENX EASY INT, the orange (V CC ) and blue (GND) connections are not used. Hall signals are then generated by an ENX EASY-INT sensor (no pull-up resistor required; output signals: CMOS compatible push-pull stage). Connection NTC (Cable AWG 26) purple NTC purple NTC Resistance 25°C: 10 kOhm ±1%, beta (25–85°C): 3490 K



September 2020 edition / provisional data / subject to change xdrives.maxongroup.com

196

maxon EC motor

Made with FlippingBook Publishing Software