AMS Solution Series & Eliminator Hoods O&M

Fume Hood O&M

Solution Series & Eliminator Series Fume Hoods

Operation & Maintenance Guide

Operation and maintenance begins with the proper start up, normally provided by your Lab Manager, Classroom Supervisor or EH&S personnel. A typical laboratory operating procedure addresses practices such as those suggested below. • Make sure the exhaust fan is operating prior to starting an experiment. • Keep experiments and equipment 6” or more from the front edge of the sash. • If possible, raise equipment off the counter top to facilitate air movement below. • Wear protective clothing such as safety goggles, gloves, and lab coasts. • Keep the sash closed except when loading or unloading the experiment. • Keep the sash window clean and clear. • Immediately clean up and major spills occurring inside the fume hood. • Remove all residues from the fume hood chamber once the experiment is complete. • Keep the light fixtures clean and replace the bulbs whenever necessary. It is recommended that a clear working environment be promoted for both safety and operation of the fume hood. It is the responsibility of the user to consult with the Lab Manager or Classroom Supervisor for additional lab safety procedures and practices. When conducting an experiment within the fume hood, it is the user’s responsibility to understand and follow the lab safety procedures and practices.

All spills inside the fume hood should be cleaned up immediately with a neutralizing compound as required by your facility manager. Spills must be flushed and cleaned thoroughly to ensure lab safety. Weekly Maintenance General maintenance or housekeeping should be done on a weekly basis. This consists primarily of cleaning the side walls, baffles, counter tops and sash of any dirt or debris that may have collected. All surfaces can be cleaned with a mild detergent and water. If a large amount of build up is present, a qualified laboratory technician should observe the contents and oversee the cleaning procedure to ensure the integrity and proper operation of the hood and the safety of lab personnel. Monthly Maintenance Glass, chain, sprocket, sash guides, and plumbing handles are the only parts that move on the fume hood. These items should be checked on a monthly basis to note and damage or excessive wear and tear. These parts should be replaced as soon as damage or excessive wear has been observed. The sash glass should be replaced if there are any chips, cracks or scratches that prevent a clear view of the interior of the fume hood.

Operation & Maintenance Guide

The cables on top of the fume hood should be replaced if there is damage to the protective coating which prevents smooth operation of the sash. Plumbing handles should turn only in a clockwise or counterclockwise direction. If the handles seem loose or wobbly, check the screw behind the index button or the cotter pin that connects the handle to the valve. Annual Maintenance The hoods must be balanced to maintain the proper air flow across the face of the fume hoods. This procedure should be performed on an annual basis to make sure all exhaust fans are performing properly, and proper air flow is being achieved. Contact your local HVAC contractor for assistance with balancing the air flow. Additional Accessories If additional accessories have been added to your specific fume hood, such as magnahelic gauges or air flow monitors, a separate manual specifically addressing those items has been supplied and should be consulted. Stainless Steel Work Surfaces Upon receipt of your order, please take care to inspect the products to be sure that they have been made to order, and that damage has not occurred in transit. There is a five day window to report any damage you should find. In this unlikely event, please contact us or the dealer that you purchased from, and we will assist you promptly.

Our stainless-steel countertops are made with a type 304 stainless steel, with a number 4, b-brushed finished. Countertops are guaranteed, under normal usage, for a one-year period from the date of receipt. This warranty is null and void if damage has occurred as a result of mistreatment or non-typical use of the product. All of our stainless steel products should be received in a shiny and new condition. To maintain that new appearance, we recommend using a stainless-steel cleaner and polish. Clean up spills and residue immediately to help maintain a new appearance. Consult with your safety officer regarding proper clean up procedures and disposal coating which prevents smooth operation of the sash. Sash Operation While operating the sash, DO NOT use excessive force to open the sash. Doing this can cause the chain/cable system to jump and cause the sash to sag, or not work entirely. If the sash becomes difficult to open, please make sure that all maintenance steps have been followed. In most cases, general maintenance will allow for the easy opening of the sash.

Solution Fume Hood

10 Tube Sash Frame w/ Glass Trim 11 Bottom Finger Lift 12 1/4” Clear Lami Safety Glass 13 Airfoil Assembly 14 RH Interior Polyresin Side Panel 15 RH Pose Front 16 RH Exterior Metal Side Panel 17 RH Frame Structural Support 18 Polyresin Top Panel

19 2-Tube T-8 Fluorescent Light 20 1/4” Clear Lami Light Glass 21 Sash Counterweight 22 Stainless Steel Cable Shaft 23 Front Sprocket for Sash Chain 24 Rear Sprocket for Sash Chain 25 #35 Roller Chain 26 Rubber Bumper (For Sash)

LH Exterior Metal Side Panel

2 LH Post Front 3 LH Frame Structural Support 4 LH Interior Polyresin Side Panel 5 Top Rear Reinforcement

6 Polyresin Back Panel 7 Upper Polyresin Baffle 8 Lower Polyresin Baffle 9 Front Panel

Eliminator 100 Series Fume Hood

10 Tube Sash Frame w/ Glass Trim 11 Bottom Finger Lift 12 1/4” Clear Lami Safety Glass 13 Airfoil 14 RH Interior Polyresin Side Panel 15 RH Pose Front 16 RH Exterior Metal Side Panel 17 RH Frame Structural Support 18 Polyresin Top Panel

19 2-Tube T-8 Fluorescent Light 20 1/4” Clear Lami Light Glass 21 Light Glass Frame 22 Stainless Steel Cable Shaft 23 Front Sheave 24 2” DIA Steel Pulley 25 7x7 Steel Coated Sash Cable 26 Rubber Bumper (For Sash)

LH Exterior Metal Side Panel

2 LH Post Front 3 LH Frame Structural Support 4 LH Interior Polyresin Side Panel 5 Top Rear Reinforcement

6 Polyresin Back Panel 7 Upper Polyresin Baffle 8 Lower Polyresin Baffle 9 Front Panel

Ceiling Enclosures & Finished Backs

Ceiling Enclosures

The ceiling enclosures are available in two types: for standard fume hoods and also for those fume hoods utilizing the optional Air Chamber. Both enclosures conceal and protect the hood ductwork, electrical conduit and other supply lines.

STEP 1 PAINTED ANGLE BOLTS TO WALL 2 PLACES

Example:

Height

CE-48-18

Width

STEP 2 ENCLOSURE END SCREWS TO OUTSIDE OF PAINTED ANGLE AND SCREWS DOWN TO TOP EDGE OF HOOD

STEP 1 PAINTED ANGLE BOLTS TO WALL 2 PLACES

STEP 2 ENCLOSURE END SCREWS TO OUTSIDE OF PAINTED ANGLE AND SCREWS DOWN TO TOP EDGE OF HOOD

STEP 3 ENCLOSURE FRONT SCREWS TO ENCLOSURE ENDS ON THE SIDE FLANGES OF THE END ENCLOSURES

Finished Back

Finished backs are used to close off the back of the fume hood, giving it a finished look when located in the center of a room.

Example:

*Width will be the same width as fume hood.

FINBACK-48

Width

Electrical Accessories & Specifications

Pre-Wire service is completed in accordance with NEC and UL-1805 standards

Note: If the fume hood is not pre-wired, wiring in the field must be accomplished using UL listed electrical fixtures while observing NEC standards and local electrical codes.

GFI

BLOWER SWITCH

CONDUIT

GREEN (Ground) WHITE (Neutral) BLACK (Hot) RED (Blower Switch Leg)

CONDUIT

GFI

LIGHT SWITCH

GREEN (Ground) WHITE (Neutral) BLACK (Hot) RED (Blower Switch Leg)

Light switch leg always wire nutted to light fixture in junction box

CONDUIT

BLACK (Hot) WHITE (Neutral) GREEN (Ground)

LIGHT FIXTURE

Single Pole 15 Amp Light Switch Standard Black Color and Cover Plate Part # LTSW

Red Illuminated Toggle Switch with Black Cover Plate Part # BLSW

Explosion Proof Outlet Class 1, Group 1 Part # XPO

Explosion Proof Switch Class 1, Group 1 Part # XSW

208 Volt, 20 Amp Single Pole Receptacle 230, 277 or other available upon request Part # 208

120 Volt, 20 Amp Ground Fault Interrupter (GFI) Duplex Outlet Standard Black color with cover Part # GFI

Explosion Proof Light Class 1, Group 1 Available in Incandescent or fluorescent Part # XPL

Laboratory Service Fixtures and Safety Equipment Installation, Operation and Maintenance Guide:

IOM-010

Contents Laboratory Service Fixtures Water Fixtures

To Our Customers: For over sixty years, WaterSaver Faucet Co. has set the standard for quality in faucets, valves and safety equipment for science laboratories. Our products are carefully designed and manufactured to provide exceptional durability and performance. However, in order to provide this durability and performance, our products must be installed correctly, operated properly, inspected regularly and maintained periodically. To assist in the installation, operation and maintenance of our products, we have developed this “IO&M Guide.” This Guide provides information on installation procedures, repair and replacement parts and trouble shooting techniques for our products. When ordering WaterSaver parts, please note the following: 1. Part numbers beginning “HK” (handle kit) are a complete assembly consisting of a valve unit, packing nut, handle and index button. These assemblies are typically used to convert a faucet from one type of handle to another, or for complete rebuilding of the faucet or valve. Handle kits are sold individually. 2. Part numbers ending in “R” are available in package quantities only. The quantity contained in the package is indicated. 3. Parts that are visible when installed (such as packing nuts and handles) are furnished with a polished chrome plated finish as standard. Special finishes (such as satin chrome finish with clear epoxy coating, satin nickel finish with clear epoxy coating and colored powder coated finishes) are available at additional cost. Please specify if a finish other than polished chrome is required. Repair and replacement parts are available on a 24-hour basis through the WaterSaver Parts Hotline. Our product specialists are available to answer questions and provide technical support. Call 1-800-WSF-PART to take advantage of this service. WaterSaver Faucet Co. is dedicated to providing quality products and service. We trust that you will let us know if we can be of assistance in any way.

Renewable Units for Water Fixtures..................................3-11 Handle/Unit Kits for Water Fixtures................................12-15 Self-Closing Renewable Units for Water Fixtures...... 16-17 Renewable Units for Foot-Operated Valves.......................18 Pure Water Fixtures Renewable Units for Pure Water Fixtures...........................19 Handle/Unit Kits for Pure Water Fixtures....................20-25 Gooseneck Components...............................................................26 Vacuum Breakers Components for Vacuum Breakers.................................27-28 Guidelines for Vacuum Breaker Installation, Operation and Maintenance..............................................29-31 Needle/Fine Control Needle/Steam Valves......................32-33 Inlet Components......................................................................34-35 Laboratory Safety Equipment Spray Heads........................................................................................36 Shower Heads....................................................................................37 Shower Valves and Actuators..................................................... 38 Bowls and Drain Fittings..............................................................39 Eyewash and Drench Hose Components...............................40 Squeeze Valves...................................................................................41 Signs...................................................................................................... 42

Steven A. Kersten President

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

Introduction

WaterSaver renewable units are manufactured in a variety of styles and configurations for the many applications in which they are used. These styles and configurations are described below: 1. Manual vs. Self-Closing Control. Typical laboratory faucets and valves are manufactured with a renewable unit that has manual (also called compression) control. The unit is manually opened and manually closed by turning the valve handle. However, in certain applications, it is desirable to have a faucet with a self-closing valve and handle. WaterSaver therefore also manufactures renewable units with a spring-loaded valve mechanism. The faucet closes automatically when the handle is released. WaterSaver manual and self-closing units are dimensionally identical and therefore interchangeable. Faucets can be converted from manual to self-closing control, and vice versa, simply by changing the faucet cartridge. 2. Round Serrated Stem vs. Tapered Square Stem. The WaterSaver renewable unit was originally manufactured with a round serrated stem end. Handles had a matching round serrated broach to fit on the stem. In 1991, we changed to a valve stem with a tapered square end. Handles were also changed to have a matching female taper. The tapered square end provides a much more solid, durable fit between the stem and handle. However, we still offer renewable units and stems with the round serrated end (the BNV100 series) for use in maintaining older faucets. 3. Right Hand Thread vs. Left Hand Thread. A typical faucet or valve is opened by rotating the handle in a counterclockwise direction. The faucet or valve is closed by turning the handle in the opposite (clockwise) direction. This rotation is called “right hand” construction, since the thread on the valve stem is a right hand thread. The vast majority of faucets manufactured by WaterSaver work in this way. However, when faucets are furnished with wrist blade or lever handles, it is preferable to have the handles open in opposite directions. For example, on an L400 series deck mounted mixing faucet, both handles should open by rotating up and close by rotating down. This requires that the valve mechanisms open in opposite directions. One of the valve mechanisms must therefore be furnished with a valve unit that has a reversed (i.e. left hand) thread. The unit with the left hand thread will open in the clockwise direction and close in a counterclockwise direction. The left hand unit is typically, though not always, installed on the cold water side of the faucet.

WaterSaver faucets utilize an interchangeable unit or cartridge that is standardized across the product line. The unit contains all working components of the water faucet or valve. There are no moving parts in the faucet or valve body itself to wear out. As a result, WaterSaver water fittings are virtually everlasting. Key features of the WaterSaver renewable unit are: • The unit has outer serrations or splines to lock the unit in position in the faucet body. The unit cannot rotate or turn as the faucet is used. The handles of the faucet will maintain position, even with lever or wrist blade handles. • The valve seat is machined from solid stainless steel bar stock. The main wearing component of the valve is thus ultra-hard and corrosion resistant for superior durability. • A hard rubber valve disc provides positive shut-off of the water flow. The valve does not have a soft or “spongy” feel that reduces the ability to meter the water flow. • The valve stem is sealed with a molded TFE packing. The packing prevents leakage over hundreds of thousands of cycles. An adjustable packing nut permits take up of wear. The WaterSaver renewable unit has been in use since the late 1940s, and has provided high performance and durability in literally millions of faucets. The overall design and dimensions of the unit have never changed. As a result, every WaterSaver faucet ever made can use the same renewable unit that goes into every faucet we make today.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

WaterSaver faucets. However, for purified water applications, the brass components of the unit are coated with a layer of pure tin. To order such units or components, add the suffix “TL” to the part number. 7. Check Valve. WaterSaver offers renewable units with an internal check valve. The purpose of the check valve is to prevent backflow of water upstream of the valve. This can be used to prevent cross-mixing of hot and cold water when the faucet is opened for a long period of time and the outlet may be closed. This can occur on units such as pre-rinse units where there is a self-closing valve downstream of the faucet valves. All WaterSaver pre-rinse units are furnished with renewable units with internal check valves. To order a renewable unit with an internal check valve, add the suffix “CV” to the part number. 8. Ceramic Disc Units. The original WaterSaver renewable unit is based on a compression valve design. The valve operates by means of a rubber disc that is compressed against a valve seat. When the handle is turned to open the faucet, the disc moves up off the seat, thus opening the waterway. When the handle is turned to close the valve, the disc is moved down to recompress against the valve seat. As an alternative to this type of construction, WaterSaver offers units that utilize rotating ceramic discs to control the water flow. The unit has two flat ceramic discs, each of which has a hole or port in it. When the handle is turned, the upper disc rotates, allowing the orifice in the upper disc to align with the orifice in the lower disc and opening the waterway. Units with rotating ceramic discs are dimensionally the same as, and thus interchangeable with, the standard WaterSaver compression renewable unit.

4. 120 Degree vs. 90 Degree Rotation. Typical WaterSaver renewable units rotate approximately 120 degrees from the closed to open position. However, when a faucet is furnished with wrist blade or lever handles, it is advantageous for the handle to go from closed to open in a 90 degree rotation. This more limited rotation prevents the handles from hitting the counter or a backsplash behind the faucet. WaterSaver therefore offers the BNV200-90 series renewable units for use in faucets with wrist blade or lever handles. 5. Adjustable Volume Control. The original WaterSaver renewable unit incorporated an adjustable volume control device. This device consists of a small round cap or thimble held in place by a set screw. By loosening the set screw and rotating the thimble, the user can adjust the size of the inlet port through which the water passes as it enters the valve. By opening or closing the port, the user can compensate for high water pressure or conserve water. Effective in 1985, the adjustable volume control device was changed from a standard to an optional feature of our products. Renewable units with the suffix “AC” include the adjustable volume control feature. 6. Tin-Lined Units. Faucets and valves for distilled, deionized and purified water must be manufactured using inert materials that are in contact with the water. These inert materials protect the purity of the water, as well as prevent the purified water from corroding the faucet or valve itself. WaterSaver manufactures faucets and valves for purified water in tin-lined brass, PVC, polypropylene, polypropylene- lined brass, PVDF-lined brass and stainless steel. This wide selection of materials permits the use of products that meet the requirements of the particular application. Faucets and valves that are tin-lined brass use the same renewable unit as all

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV100 Renewable Unit, Compression Control, Round Serrated Stem, Right Hand Thread BNV100LH Renewable Unit, Compression Control, Round Serrated Stem, Left Hand Thread

Renewable Unit, Compression Control, Right Hand Thread Cartridge rotates counterclockwise to open. Renewable Unit, Compression Control, Left Hand Thread Cartridge rotates clockwise to open.

BNV100

BNV100LH

BNV060R

Packing Nut O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

BNV065AS-R Valve Stem Packing

with Internal O-Ring (pkg of 6) Retainer Washer (pkg of 6)

SNV055R SNV050R

Stem Friction Ring (pkg of 6)

bnv045R Valve Stem, Round Serrated End, Right Hand Thread (pkg of 6) bnv045LH-R Valve Stem, Round Serrated End, Left Hand Thread (pkg of 6)

SNV036-045R Valve Stem with Disc and Screw (Assembled), Right Hand Thread (pkg of 6) SNV036-045LH-R Valve Stem with Disc and Screw (Assembled), Left Hand Thread (pkg of 6)

BNV040R

Valve Disc (pkg of 6)

SNV036R

Valve Disc Screw (pkg of 6)

BNV030-130A-R Barrel and Seat (Assembled), Right Hand Thread (pkg of 6) BNV030LH-130A-R Barrel and Seat (Assembled), Left Hand Thread (pkg of 6)

BNV030R Barrel, Right Hand Thread (pkg of 6) BNV030LH-R Barrel, Left Hand Thread (pkg of 6)

SNV130A-R

Stainless Steel Seat With BNV025 Unit Washer (Assembled) (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV100AC Renewable Unit, Compression Control, Round Serrated Stem, Right Hand Thread, with Adjustable Volume Control BNV100AC-LH Renewable Unit, Compression Control, Round Serrated Stem, Left Hand Thread, with Adjustable Volume Control

BNV100AC Renewable Unit, Compression Control, Right Hand Thread, with Adjustable Volume Control Cartridge rotates counterclockwise to open. BNV100AC-LH Renewable Unit, Compression Control, Left Hand Thread, with Adjustable Volume Control Cartridge rotates clockwise to open.

BNV060R

Packing Nut O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

BNV065AS-R

Valve Stem Packing with Internal O-Ring (pkg of 6) Retainer Washer (pkg of 6) Stem Friction Ring (pkg of 6)

SNV055R SNV050R

SNV036-045R Valve Stem with Disc and Screw (Assembled), Right Hand Thread (pkg of 6) SNV036-045LH-R Valve Stem with Disc and Screw (Assembled), Left Hand Thread (pkg of 6) SNV005-030R Barrel and Seat with Adjustable Volume Control (Assembled), Right Hand Thread (pkg of 6) SNV005-030LH-R Barrel and Seat with Adjustable Volume Control (Assembled), Left Hand Thread (pkg of 6)

bnv045R

Valve Stem, Round Serrated End, Right Hand Thread (pkg of 6) Valve Stem, Round Serrated End, Left Hand Thread (pkg of 6)

bnv045LH-R

BNV040R

Valve Disc (pkg of 6)

SNV036R

Valve Disc Screw (pkg of 6)

BNV030R

Barrel, Right Hand Thread (pkg of 6) Barrel, Left Hand Thread (pkg of 6)

BNV030LH-R

SNV015R

Stainless Steel Seat for Adjustable Volume Control (pkg of 6)

BNV025R BNV010R SNV005R

Unit Washer (pkg of 6)

WaterSaver Volume Control (pkg of 6)

Set Screw (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV200

Renewable Unit, Compression Control, Tapered Square Stem, Right Hand Thread Note: For use in faucets with four-arm handles.

BNV200

Renewable Unit, Compression Control, Right Hand Thread Cartridge rotates 120 degrees counterclockwise to open.

BNV060R

Packing Nut O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

BNV065AS-R

Valve Stem Packing with Internal O-Ring (pkg of 6) Retainer Washer (pkg of 6)

SNV055R SNV050R

Stem Friction Ring (pkg of 6)

bnv045TS-R

Valve Stem, Tapered Square End, Right Hand Thread (pkg of 6)

SNV036-045TS-R Valve Stem With Disc And Screw (Assembled), Right Hand Thread (pkg of 6)

BNV040R

Valve Disc (pkg of 6)

SNV036R

Valve Disc Screw (pkg of 6)

BNV030-130A-R Barrel and Seat (Assembled), Right Hand Thread (pkg of 6)

BNV030R

Barrel, Right Hand Thread (pkg of 6)

SNV130A-R

Stainless Steel Seat With BNV025 Unit Washer (Assembled) (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV200-90 Renewable Unit, Compression Control, Tapered Square Stem, Right Hand Thread, 90 Degree Rotation BNV200LH-90 Renewable Unit, Compression Control, Tapered Square Stem, Left Hand Thread, 90 Degree Rotation

Note: For use in faucets with wrist blade and lever handles.

BNV200-90 Renewable Unit, Compression Control, Right Hand Thread, 90 Degree Rotation Cartridge rotates 90 degrees counterclockwise to open. BNV200LH-90 Renewable Unit, Compression Control, Left Hand Thread, 90 Degree Rotation Cartridge rotates 90 degrees clockwise to open. BNV060R Packing Nut O-Ring (pkg of 6) BNV065AS-R Valve Stem Packing with Internal O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

SNV055R

Retainer Washer (pkg of 6)

SNV050R

Stem Friction Ring (pkg of 6) (2 required)

SNV036-045TS-R Valve Stem with Disc and Screw (Assembled), Right Hand Thread (pkg of 6) SNV036-045TS-LH-R Valve Stem with Disc and Screw (Assembled), Left Hand Thread (pkg of 6)

bnv045TS-R Valve Stem, Tapered Square End, Right Hand Thread (pkg of 6) bnv045TS-LH-R Valve Stem, Tapered Square End, Left Hand Thread (pkg of 6)

BNV040R

Valve Disc (pkg of 6)

SNV036R

Valve Disc Screw (pkg of 6)

BNV030-130A-R Barrel and Seat (Assembled), Right Hand Thread (pkg of 6) BNV030LH-130A-R Barrel and Seat (Assembled), Left Hand Thread (pkg of 6)

BNV030R

Barrel, Right Hand Thread (pkg of 6) Barrel, Left Hand Thread (pkg of 6)

BNV030LH-R

SNV130A-R

Stainless Steel Seat With BNV025 Unit Washer (Assembled) (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV200AC Renewable Unit, Compression Control, Tapered Square Stem, Right Hand Thread, with Adjustable Volume Control Note: For use in faucets with four-arm handles.

BNV200AC

Renewable Unit, Compression Control, Right Hand Thread, with Adjustable Volume Control Cartridge rotates 120 degrees counterclockwise to open.

BNV060R

Packing Nut O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

BNV065AS-R

Valve Stem Packing with Internal O-Ring (pkg of 6) Retainer Washer (pkg of 6) Stem Friction Ring (pkg of 6)

SNV055R SNV050R

bnv045TS-R

Valve Stem, Tapered Square End, Right Hand Thread (pkg of 6)

SNV036-045TS-R Valve Stem with Disc and Screw (Assembled), Right Hand Thread (pkg of 6)

BNV040R

Valve Disc (pkg of 6)

SNV036R

Valve Disc Screw (pkg of 6)

BNV030R

Barrel, Right Hand Thread (pkg of 6)

SNV005-030R Barrel and Seat with Adjustable Volume Control (Assembled), Right Hand Thread (pkg of 6)

SNV015R

Stainless Steel Seat for Adjustable Volume Control (pkg of 6)

BNV025R BNV010R SNV005R

Unit Washer (pkg of 6)

WaterSaver Volume Control (pkg of 6)

Set Screw (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV200AC-90 Renewable Unit, Compression Control, Tapered Square Stem, Right Hand Thread, 90 Degree Rotation, with Adjustable Volume Control BNV200AC-LH-90 Renewable Unit, Compression Control, Tapered Square Stem, Left Hand Thread,

90 Degree Rotation, with Adjustable Volume Control Note: For use in faucets with wrist blade and lever handles.

BNV200AC-90 Renewable Unit, Compression Control, Right Hand Thread, with

Adjustable Volume Control Cartridge rotates 90 degrees counterclockwise to open. Renewable Unit, Compression Control, Left Hand Thread, with Adjustable Volume Control Cartridge rotates 90 degrees clockwise to open.

BNV200AC- LH-90

BNV060R

Packing Nut O-Ring (pkg of 6)

BNV100 SERIES Round Serrated Stem

BNV200 SERIES Tapered Square Stem

BNV065AS-R

Valve Stem Packing with Internal O-Ring (pkg of 6) Retainer Washer (pkg of 6) Stem Friction Ring (pkg of 6) (2 required)

SNV055R

SNV050R

SNV036-045TS-R Valve Stem with Disc and Screw (Assembled), Right Hand Thread (pkg of 6) SNV036-045TS-LH-R Valve Stem with Disc and Screw (Assembled), Left Hand Thread (pkg of 6) SNV005-030R Barrel and Seat with Adjustable Volume Control (Assembled), Right Hand Thread (pkg of 6) SNV005-030LH-R Barrel and Seat with Adjustable Volume Control (Assembled), Left Hand Thread (pkg of 6)

bnv045TS-R Valve Stem, Tapered Square End, Right Hand Thread (pkg of 6) bnv045TS-LH-R Valve Stem, Tapered Square End, Left Hand Thread (pkg of 6) BNV040R Valve Disc (pkg of 6) SNV036R Valve Disc Screw (pkg of 6)

BNV030R

Barrel, Right Hand Thread (pkg of 6) Barrel, Left Hand Thread (pkg of 6)

BNV030LH-R

SNV015R

Stainless Steel Seat for Adjustable Volume Control (pkg of 6)

BNV025R BNV010R SNV005R

Unit Washer (pkg of 6)

WaterSaver Volume Control (pkg of 6)

Set Screw (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Water Fixtures

BNV300 Ceramic Disc Renewable Units

BNV300-180

Ceramic Disc Renewable Unit Cartridge rotates 180 degrees counter clockwise to open.

BNV300-90

Ceramic Disc Renewable Unit Cartridge rotates 90 degrees counter clockwise to open.

BNV300LH-90 Ceramic Disc Renewable Unit Cartridge rotates 90 degrees clockwise to open.

BNV400

Ceramic Disc Renewable Unit for Single Handle Mixing Faucets

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Water Fixtures

HK013-200 Handle/Unit Kit with BA013TS Four Arm Handle and BNV200 Renewable Unit

PA032

Index Button (specify color and service)

SF011

Handle Screw

SF012

Lockwasher

BA013TS

Four-Arm Handle

HK013-200 Handle/Unit Kit (Assembled)

BNV090

Packing Nut

bnv060

Packing Nut O-Ring

BNV200

Renewable Unit

Notes: 1. Specify color and service for index button when ordering.

2. If tin lining for distilled, deionized or purified water is required, add suffix “TL”. 3. If vandal-resistant packing nut with set screw is required, add suffix “VR”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Water Fixtures

HK013-200AC Handle/Unit Kit with BA013TS Four Arm Handle and BNV200AC Renewable Unit

PA032

Index Button (specify color and service)

SF011

Handle Screw

SF012

Lockwasher

BA013TS

Four-Arm Handle

HK013-200AC Handle/Unit Kit (Assembled)

BNV090

Packing Nut

bnv060

Packing Nut O-Ring

BNV200AC Renewable Unit with

Adjustable Volume Control

Notes: 1. Specify color and service for index button when ordering.

2. If tin lining for distilled, deionized or purified water is required, add suffix “TL”. 3. If vandal-resistant packing nut with set screw is required, add suffix “VR”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Water Valves

HK044-200-90 Handle/Unit Kit with BA044TS Wrist Blade Handle and BNV200-90 Renewable Unit, Right Hand Thread HK044-200LH-90 Handle/Unit Kit with BA044TS Wrist Blade Handle and BNV200LH-90 Renewable Unit, Left Hand Thread

PA032

Index Button (specify color and service) Handle Screw

SF011

SF012

Lockwasher

BA044TS

Wrist Blade Handle with Integral Cover

HK044-200-90 Handle/Unit Kit (Assembled)

BNV090

Packing Nut

bnv060

Packing Nut O-Ring

BNV200-90 Renewable Unit, Right Hand Thread, 90 degree rotation BNV200LH-90 Renewable Unit,

Left Hand Thread, 90 degree rotation

Notes: 1. Specify color and service for index button when ordering.

2. If tin lining for distilled, deionized or purified water is required, add suffix “TL”. 3. If vandal-resistant packing nut with set screw is required, add suffix “VR”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Water Valves

HK044-200AC-90 Handle/Unit Kit with BA044TS Wrist Blade Handle and BNV200AC-90 Renewable Unit, Right Hand Thread HK044-200AC-LH-90 Handle/Unit Kit with BA044TS Wrist Blade Handle and BNV200AC-LH-90 Renewable Unit, Left Hand Thread

PA032

Index Button (specify color and service)

SF011

Handle Screw

SF012

Lockwasher

BA044TS

Wrist Blade Handle with Integral Cover

HK044-200AC-90 Handle/Unit Kit (Assembled)

BNV090

Packing Nut

bnv060

Packing Nut O-Ring

BNV200AC-90

Renewable Unit with Adjustable Volume Control,

Right Hand Thread, 90 degree rotation BNV200AC-LH-90 Renewable Unit with

Adjustable Volume Control, Left Hand Thread, 90 degree rotation

Notes: 1. Specify color and service for index button when ordering.

2. If tin lining for distilled, deionized or purified water is required, add suffix “TL”. 3. If vandal-resistant packing nut with set screw is required, add suffix “VR”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Self-Closing Renewable Units for Water Fixtures

BSC135 Renewable Unit, Self-Closing Control BSC135LE Same as above except with BA030 Self-Closing Lever Handle

PA031

Index Button (specify color and service) Locking Clip (pkg of 6)

BSC080R

SSC085R PSC052R

Hex Adjustment Nut (pkg of 6)

Friction Washer (pkg of 6)

PA035

White Nylon Self-Closing Handle

BSC091R

Roller Bearing Assembly

BSC135 Renewable Unit, Self-Closing Control (assembled)

BSC071A-R

Packing Nut (pkg of 6)

BSC066R BNV060R SSC056R

Stem Packing (pkg of 6)

Packing Nut O-Ring (pkg of 6) Retainer Washer (pkg of 6)

SSC095R

Lifting Spring (pkg of 6)

BSC046R

Valve Stem (pkg of 6)

BNV040R SNV036R

Valve Disc (pkg of 6)

Valve Disc Screw (pkg of 6)

BSC032R

Barrel (pkg of 6)

BSC032-130A-R Barrel With Seat (Assembled) (pkg of 6)

SNV130A-R Stainless Steel Seat With BNV025 Unit Washer (Assembled)

Note: If tin lining for distilled, deionized or purified water is required, add suffix “TL”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Self-Closing Renewable Units for Water Fixtures

BSC135AC Renewable Unit, Self-Closing Control, Adjustable Volume Control BSC135AC-LE Same as above except with BA030 Self-Closing Lever Handle PA031

Index Button (specify color and service) Locking Clip (pkg of 6)

BSC080R SSC085R PSC052R

Hex Adjustment Nut (pkg of 6)

Friction Washer (pkg of 6)

PA035

White Nylon Self-Closing Handle

BSC091R

Roller Bearing Assembly

BSC071A-R BSC066R BNV060R SSC056R

Packing Nut (pkg of 6) Stem Packing (pkg of 6)

BSC135AC Renewable Unit, Self-Closing Control, Adjustable Volume Control (assembled)

Packing Nut O-Ring (pkg of 6) Retainer Washer (pkg of 6)

SSC095R

Lifting Spring (pkg of 6)

BSC046R

Valve Stem (pkg of 6)

BNV040R SNV036R

Valve Disc (pkg of 6)

Valve Disc Screw (pkg of 6)

BSC032R

Barrel (pkg of 6)

SNV015R

Stainless Steel Seat for Adjustable Volume Control (pkg of 6)

BNV025R BNV010R SNV005R

Unit Washer (pkg of 6)

BSC005-032R Barrel With Seat and Volume Control (Assembled) (pkg of 6)

WaterSaver Volume Control (pkg of 6)

Set Screw (pkg of 6)

Note: If tin lining for distilled, deionized or purified water is required, add suffix “TL”.

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Foot-Operated Valves

BSC011 / 016 / 021 Renewable Units for Foot-Operated Valves

WaterSaver foot-operated valves were redesigned as of April 1, 1995. Some of the new individual valve components (such as the valve stem and bonnet) are not interchangeable with the old components. Therefore, components for foot-operated valves are sold as complete units only.

BSC011

Renewable Unit for L3001 / 3050 Foot-Operated Valves

PSC130R

Unit Gasket (pkg of 6)

BSC016

Renewable Unit For L3010 / 3060 Foot-Operated Valves

PSC130R

Unit Gasket (pkg of 6)

BSC021

Renewable Unit for L3001LP / 3050LP Foot-Operated Valves

PSC130R

Unit Gasket (pkg of 6)

Notes: 1. If tin lining for distilled, deionized or purified water is required, add suffix “TL”. 2. If extra heavy ( 5/32 ” thick) unit gasket is required, order PSC130A-R (pkg of 6).

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Renewable Units for Pure Water Fixtures

PV100 PV100PP

Renewable Unit, Compression Control, PVC Construction Renewable Unit, Compression Control, Polypropylene Construction

PV100CPVC Renewable Unit, Compression Control, CPVC Construction PA032

Index Button (specify color and service)

BF001R

Handle Screw (pkg of 6)

BF002R

Lockwasher (pkg of 6)

PA021A

White Nylon Four-Arm Handle with Straight Square Broach

PV103R

Packing Nut (pkg of 6)

PV106R

Packing Nut O-Ring (pkg of 6)

PV102R

Valve Bonnet (pkg of 6)

PV105R

Bonnet O-Ring (pkg of 6)

PV100 Renewable Unit

PV101PP-108R Valve Stem with Straight

Square End and PV108 Valve Disc (assembled) (pkg of 6)

PV109PP-R

Replaceable Valve Seat (pkg of 6)

PV110R

Valve Seat O-Ring (pkg of 6)

Note: When ordering components individually, specify material required (PVC, polypropylene or CPVC).

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK019-7800 Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Compression Control (Old Style) Note: This handle/unit kit is for use in L7833/7834/7837/7838/7840/7844 polypropylene- or PVDF- lined pure water fixtures. These fixtures were redesigned in 2002. Fixtures manufactured prior to 2002 utilize a valve body with a female thread (as shown). Fixtures manufactured after 2002 utilize a valve body with a male thread. This HK019- 7800 handle/unit kit is for fixtures manufactured prior to 2002. HK019-7800 Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Compression Control (Old Style)

2 3

8 9 10

ITEM PART NO.

DESCRIPTION

PV116B-R PV120A-R 600-228R BV112B-R

Molded Diaphragm (pkg of 6) Valve Stem Cap (pkg of 6) O-Ring (2 required) (pkg of 12) Valve Stem (pkg of 6) Bonnet Gasket (pkg of 6)

2 3 4 5 6

PV147R

BV107D-R

Valve Bonnet with Male Thread (pkg of 6)

PA019WHT White Nylon Round Handle

SF012R SNV035R PA032 PO119R PO118R BO108R

Lockwasher (pkg of 6) Handle Screw (pkg of 6)

8 9

Index Button (specify color and service)

Hose End O-Ring (pkg of 6)

Hose End (pkg of 6) Outlet Nut (pkg of 6)

12 13

Note: RK7800R repair kit includes: (6) PV116B diaphragms (6) PV120A valve stem caps (12) 600-228 O-rings (6) PV147 bonnet gaskets

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK019-7800A Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Compression Control (New Style) Note: This handle/unit kit is for use in L7833/7834/7837/7838/7840/7844 polypropylene- or PVDF- lined pure water fixtures. These fixtures were redesigned in 2002. Fixtures manufactured prior to 2002 utilize a valve body with a female thread. Fixtures manufactured after 2002 utilize a valve body with a male thread (as shown). This HK019- 7800A handle/unit kit is for fixtures manufactured after 2002.

HK019-7800A Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Compression Control (New Style)

2 3

7 8

10 11

ITEM PART NO.

DESCRIPTION

PV116B-R PV120A-R 600-228R BV112B-R BV148A-R SF004R SF012R SNV035R PV147R BV146R

Molded Diaphragm (pkg of 6) Valve Stem Cap (pkg of 6) O-Ring (2 required) (pkg of 12) Valve Stem (pkg of 6) Bonnet Gasket (pkg of 6) Valve Bonnet (pkg of 6) Retainer Nut (pkg of 6)

2 3 4 5 6

Set Screw (pkg of 6)

8 9

PA019WHT White Nylon Round Handle

Lockwasher (pkg of 6) Handle Screw (pkg of 6)

PA032 PO119R PO118R BO108R

Index Button (specify color and service)

12 13 14 15

Hose End O-Ring (pkg of 6)

Note: RK7800R repair kit includes: (6) PV116B diaphragms (6) PV120A valve stem caps (12) 600-228 O-rings (6) PV147 bonnet gaskets

Hose End (pkg of 6) Outlet Nut (pkg of 6)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK019-7850 Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Compression Control

Note: This handle/unit kit is for use in L7853/7854 polypropylene- or PVDF- lined pure water fixtures.

HK019-7850 Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Compression Control

2 3

9 10

ITEM PART NO.

DESCRIPTION

PV116B-R PV120A-R 600-228R BV112D-R

Molded Diaphragm (pkg of 6) Valve Stem Cap (pkg of 6) O-Ring (2 required) (pkg of 12) Valve Stem (pkg of 6) Bonnet Gasket (pkg of 6)

2 3 4 5 6

PV147R BV142R B0391R

Barrel (pkg of 6)

Retainer Nut (pkg of 6)

PA019WHT White Nylon Round Handle

8 9

SF012R SNV035R

Lockwasher (pkg of 6) Handle Screw (pkg of 6)

PA032

Index Button (specify color and service)

Note: RK7800R repair kit includes: (6) PV116B diaphragms (6) PV120A valve stem caps (12) 600-228 O-rings (6) PV147 bonnet gaskets

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK035-7850SC Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Self-Closing Control HK030-7850SC Same as above except with BA030 Self-Closing Lever Handle Note: This handle/unit kit is for use in L7853SC/7853SC-LE/7854SC/7854SC-LE polypropylene- or PVDF- lined pure water fixtures.

HK035-7850SC Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Self-Closing Control

1 2

6 7

9 10 1112 13 14

ITEM PART NO.

DESCRIPTION

PV116B-R PV147R BV112C-R SSC095R SSC056R BNV060R

Molded Diaphragm (pkg of 6) Bonnet Gasket (pkg of 6)

2 3 4 5 6

BV118SC-R Self-Closing Barrel (pkg of 6)

Self-Closing Valve Stem (pkg of 6) Lifting Spring (pkg of 6) Retainer Washer (pkg of 6) Packing Nut O-Ring (pkg of 6)

BSC071A-R Packing Nut (pkg of 6)

8 9

BSC091R

Roller Bearing Assembly (pkg of 6) White Nylon Self-Closing Handle

PA035

PSC052R SSC085R BSC080R

Friction Washer (pkg of 6)

Hex Adjustment Nut (pkg of 6)

12 13 14

Locking Clip (pkg of 6)

PA031

Index Button (specify color and service)

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK080C-7800SC Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Self-Closing Control Note: This handle/unit kit is for use in L7833SC/7834SC/7840SC polypropylene- or PVDF- lined pure water fixtures.

HK080C-7800SC Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Self-Closing Control

2 3

6 7 8

ITEM PART NO.

DESCRIPTION

PV116B-R BV144R BV143R SV086R PV147R BV145R BV148A-R SF004R

Molded Diaphragm (pkg of 6) Brass Stem Cap (pkg of 6) Self-Closing Valve Stem (pkg of 6)

2 3 4 5 6

Spring (pkg of 6)

Bonnet Gasket (pkg of 6) Valve Bonnet (pkg of 6) Retainer Nut (pkg of 6) Set Screw (pkg of 6)

8 9

BV082A-R Screw and Post (pkg of 6)

PA080C PO119R PO118R BO108R

White Nylon Self-Closing Handle

Hose End O-Ring (pkg of 6)

Hose End (pkg of 6) Outlet Nut (pkg of 6)

12 13

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Handle/Unit Kits for Pure Water Fixtures

HK080B-7800MSC Handle/Unit Kit for Polypropylene- or PVDF- Lined Pure Water Fixtures, Manual/Self-Closing Control Note: This handle/unit kit is for use in L7833MSC/7834MSC/7840MSC polypropylene- or PVDF- lined pure water fixtures. HK080B-7800MSC Handle/Unit Kit, Polypropylene-Lined Pure Water Fixtures, Manual/Self-Closing Control

2 3

6 7 8

ITEM PART NO.

DESCRIPTION

PV116B-R BV144R BV143R SV086R PV147R BV145R BV148A-R SF004R

Molded Diaphragm (pkg of 6) Brass Stem Cap (pkg of 6) Self-Closing Valve Stem (pkg of 6)

2 3 4 5 6

Spring (pkg of 6)

Bonnet Gasket (pkg of 6) Valve Bonnet (pkg of 6) Retainer Nut (pkg of 6) Set Screw (pkg of 6)

8 9

BV082A-R Screw and Post (pkg of 6)

PA080B PO119R PO118R BO108R

White Nylon Manual/Self-Closing Handle

Hose End O-Ring (pkg of 6)

Hose End (pkg of 6) Outlet Nut (pkg of 6)

12 13

WaterSaver Faucet 701 W Erie St Chicago, IL 60654

312 666 5500 telephone 312 666 5501 facsimile wsflab.com

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46-47 Page 48-49 Page 50 Page 51 Page 52 Page 53 Page 54

airmastersystems.com

Made with FlippingBook Digital Proposal Creator