HYDRAULIC PUMPS
CLUTCH PUMPS
CYLINDERS
CP124 CLUTCH PUMPS
• Heavy duty sleeve bushing design in a small frame • Doweled and high strength 3 piece cast iron construction • High strength alloy steel gear and shaft set • Pressure balanced wear plates maintain high pump efficiency • High torque clutches in most popular configurations
CYLINDER COMPONENTS
• SAE A mounting with bracket or pad mounting • Side and rear 1/4” NPT inlet and 3/4” NPT outlets • Fixed displacement CID = Cubic Inch Displacement - the amount of oil that is discharged in one revolution of the gears Flow Rate (gpm) = Displacement (CID) X Speed (rpm) / 231
JACKS
VALVES
PART NO.
ROTA- TION
INLET PORT
OUTLET PORT
CID
GPM
RPM
PSI
MOUNTING
MOTORS
2 Bolt A Mount Pump Only - No Mounting Bracket or Clutch
252267 252269 252270 252271 252272 252273 252274 252275 252276 252277 252278 252279 252280 252281
CW 0.93 CW 1.86 CW 2.48
10.8 21.7 29.0
3000 Max / 600 Min 3000 Max / 600 Min 3000 Max / 600 Min
3500 3200 2500
1 1/4 NPT 3/4 NPT 1 1/4 NPT 3/4 NPT 1 1/4 NPT 3/4 NPT
2 bolt A or Pad 2 bolt A or Pad 2 bolt A or Pad
PUMPS
2 Bolt A Mount Pump With 4 Hole Foot Mounting Bracket and Clutch
1 1/4 NPT 3/4 NPT 2 bolt A bracket | K6 Groove 1 1/4 NPT 3/4 NPT 2 bolt A bracket | K8 Groove 1 1/4 NPT 3/4 NPT 2 bolt A bracket | AA V Belt
CW 1.86 CW 2.48 CW 2.48
21.7 29.0 29.0
3000 Max / 600 Min 3000 Max / 600 Min 3000 Max / 600 Min
3200 2500 2500
ENGINES
2 Bolt A Mount Pump With 2 Hole Foot Mounting Pad/Clutch Not Included
CW 0.93 CW 1.55 CW 1.86
10.8 18.1 21.7
3000 Max / 600 Min 3000 Max / 600 Min 3000 Max / 600 Min
3500 3500 3200
1 1/4 NPT 3/4 NPT 1 1/4 NPT 3/4 NPT 1 1/4 NPT 3/4 NPT
Mounting Pad Mounting Pad Mounting Pad
POWER UNITS
Accessories
AA Groove clutch assembly 120 lb. ft. torque
Type K, 6 groove serpentine clutch assembly 120 lb. ft. torque Type K, 8 groove serpentine clutch assembly 120 lb. ft. torque
FILTRATION
Clutch pump bracket - 2 Bolt A flanges
Clutch pump switch kit
GAUGES & METERS
PTO GEAR PUMPS
CONTROLS
CHIEF™ - PTO Gear Pumps
FLUID COOLERS
• Power Take Off gear Pump • Aluminum center section and cast iron end plates • Fixed displacement
• SAE Side or Rear Ports • Oil Temp: -12F - 175F • Inlet Port (suction) is the larger port **Drive Shaft Required** CID = Cubic Inch Displacement - the amount of oil that is discharged in one revolution of the gears Flow Rate (gpm) = Displacement (CID) X Speed (rpm) / 231
HOSES & FITTINGS
COMPONENTS
* HP needed to run pump
BEARINGS & BUSHINGS
PART NO.
INLET PORT
OUTLET PORT
HP
CID
GPM
RPM
PSI
Aluminum Center Housing - 6 Tooth Spline - 1 3/8” Diameter**
252567 252557 252555 252560
8
3.41 5.50 7.62 9.76
7.40 12.00 16.60 21.00
540 540 540 540
2500 2500 2500 2500
SAE 16 SAE 16 SAE 16 SAE 16
SAE 12 SAE 12 SAE 12 SAE 12
MOBILE PRODUCTS
13 20 21
Aluminum Center Housing - 21 Tooth Spline - 1 3/8” Diameter**
CUSTOM SOLUTIONS
252565 252566** 252568
25 43
5.50 9.76
22.10 39.30
1000 1000
2500 2500
SAE 16 SAE 20
SAE 12 SAE 16
Seal Kit 252554 Seal Kit for 252566 - rear ports**
For pricing, please refer to our website at Baileyhydraulics.com or call one of our Customer Experience Specialists at 1-800-800-1810.
94
Made with FlippingBook flipbook maker