New Products: Link Clamps

World’s First Screw-In Cartridge Mount Link Clamps and Twin Lever Link Clamps.

C R E A T I N G N E W E X P E C TA T I ON S World’s First Screw-In Cartridge Mount Link Clamps and Twin Lever Link Clamps

CARTRIDGE MOUNT LINK CLAMP DOUBLE ACTING SINGLE LEVER

TWIN LEVER LINK CLAMP DOUBLE ACTING ROTARY LUG

TWIN LEVER LINK CLAMP DOUBLE ACTING CARTRIDGE MOUNT

www.vektek.com

NEW

SCREW-IN TWIN LEVER LINK CLAMP DOUBLE ACTING CARTRIDGE MOUNT DESIGN WITH PATENTED EQUALIZING SYSTEM!

 Patented rotary lug feature delivers 360 degrees of lever/body positioning. This permits a cartridge mount body with no need for thread clocking.  Made possible by Vektek’s patented pivot equalizing system!  Available in 3 sizes, 1100lb, 1700lb, and 2600lb total clamping force at 5000 PSI.  Significantly increased vertical clamping stroke over standard link clamp allows access to clamp through a hole onto the surface of work piece.  Clamp on two parts with one link clamp or reach through a part hole.  For clamping when work piece surfaces are within 0.060 inches.  Cartridge mount body is manifold mount only.  Cartridge mount body minimizes clamp footprint with simple and easy to machine cavity.  Levers sold separately.

U.S. Patent No. 8,678,362 Other Patents Pending

SPECIFICATIONS

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Total clamping force is divided equally between each side. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) Concentric design allows reaching up through a bore to clamp a single part. ** Equal to ±10° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

Effective Piston Area (sq. in.)

Vertical Clamping Stroke (in)**

Oil Capacity (cu. in.)

Maximum Flow Rate*** (cu. in./min.)

Clamping Capacity (lb)*

Model No.

Extend Extend Retract Double Acting (D/A) Cylinders, actuated hydraulically both directions.

16-4215-20 1,100 16-4218-20 1,700 16-4222-20 2,600

0.18 0.24 0.29

0.274 0.394 0.616

0.141 0.051 0.259 0.080 0.511 0.186

17 31 61

Force equally divided between each side

10 CLAMP ANGLE

A THREAD D

AB CONTACT POINT

Vektek’s patented Pivot Equalizing System equally divides force between each side and allows height variations.

G HEX

AB CONTACT POINT

ILS160016 REV A

N TOTAL STROKE

For proper sealing, the mating surface must be flat within .002 in. with a maximum 63 µin R a surface finish.

M CLAMP STROKE

DIMENSIONS (IN)

Model No.

C D E

G H J

Double Acting (D/A) Cylinder, actuated hydraulically both directions. 16-4215-20 1 3/4 - 16 3.63 3.32 1.37 2.77 0.59 2.00 0.47 0.16 1.66 16-4218-20 2 - 16 4.25 3.89 1.48 3.25 0.74 2.50 0.59 0.19 1.91 16-4222-20 2 1/4 - 16 4.91 4.45 1.51 3.68 0.97 3.00 0.71 0.20 2.15 Model No. L M N T AB AD AF AG AH 16-4215-20 1.25 0.51 0.64 2.188 1.38 54 2.97 2.24 0.846 16-4218-20 1.29 0.65 0.86 2.750 1.70 56 3.46 2.56 1.063 16-4222-20 1.31 0.83 1.07 3.250 2.03 54 4.02 2.90 1.201

NEW TWIN LEVER LINK CLAMP DOUBLE ACTING ROTARY LUG DESIGN WITH PATENTED EQUALIZING SYSTEM!

 Made possible by Vektek’s patented equalizing system!  Patented rotary lug feature delivers 360 degrees of lever/body positioning. This simplifies internal porting and fixture design flexibility.  Available in 3 sizes, 1100lb, 1700lb, and 2600lb total clamping force at 5000 PSI.  Significantly increased vertical clamping stroke over standard link clamp allows access to clamp through a hole onto the surface of work piece.  Clamp on two parts with one link clamp.  For clamping when work piece surfaces are within 0.060 inches.  Top flange body can be manifold mounted or plumbed.  Levers sold separately.  Optional In The Port Flow Control is a meter-in device with reverse free flow check valve.  Optional In The Port Sequence Valve is a sequencing device with reverse free flow check valve. SPECIFICATIONS

U.S. Patent No. 8,678,362 Other Patents Pending

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Total clamping force is divided equally between each side. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) ** Equal to ±10° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

Effective Piston Area (sq. in.)

Vertical Clamping Stroke (in.)**

Oil Capacity (cu. in.)

Maximum Flow Rate*** (cu. in./min.)

Clamp Capacity (lbs)*

Model No.

Extend Extend Retract Double Acting (D/A) Cylinders, actuated hydraulically both directions.

16-3215-20 1,100 16-3218-20 1,700 16-3222-20 2,600

0.18 0.24 0.29

0.274 0.394 0.616

0.141 0.051 0.258 0.080 0.509 0.186

17 31 61

Port Depth for Optional In-Port Valves: SAE 4 X .58 In-port valves require the use of manifold mount ports

Force equally divided between each side

AA UNCLAMP PORT W UNCLAMP MANIFOLD PORT O-RING

10 CLAMP ANGLE

AB CONTACT POINT

AA CLAMP PORT

K THRU J

W CLAMP MANIFOLD PORT O-RING

ILS160013 REV A

N TOTAL STROKE

M CLAMP STROKE

For proper sealing, the mating surface must be flat within .003 in. with a maximum 63 µin R a surface finish.

DIMENSIONS (IN)

Model No.

A B

D E F G

H J

K L

M N P

Double Acting (D/A) Cylinders, actuated hydraulically both directions. 16-3215-20 1.408 2.94 2.64 1.008 2.09 1.28 0.67 0.47 0.38 0.22 0.88 0.51 0.64 1.969 0.984 16-3218-20 1.566 3.35 2.99 1.248 2.34 1.32 0.67 0.59 0.44 0.28 0.83 0.65 0.86 2.441 1.220 16-3222-20 1.881 3.76 3.31 1.508 2.54 1.34 0.67 0.71 0.53 0.34 0.75 0.83 1.07 2.953 1.476

Model No.

R S T V W X Y Z AA AB AD AF AG AH

16-3215-20 0.797 0.797 2.402 0.984 2-011 0.433 1.093 0.43 SAE 4 1.38 54 2.283 1.555 0.846 16-3218-20 0.985 0.985 2.835 1.220 2-011 0.551 1.289 0.55 SAE 4 1.70 56 2.559 1.654 1.063 16-3222-20 1.188 1.188 3.445 1.476 2-011 0.630 1.644 0.63 SAE 4 2.03 54 2.874 1.752 1.201

CARTRIDGE MOUNT LINK CLAMP CAVITY DIMENSIONS .002

-A-

(D MIN) (B MIN)

A THREAD UN-2B B MIN MINOR C .007 D MIN 90° X E .002 A F MAX ON OR INSIDE G RADIUS CLAMP FEED

R.020 MAX

(G RADIUS)

(J RADIUS)

H MAX ON J RADIUS UNCLAMP FEED

ILS160020 REV A

.150 MIN 2 PLCS

DIMENSIONS (IN)

INSTALLATION TORQUE

Model No.

C D E

G H J

Cartridge Mount, TuffLink TM 360 Single and Twin Lever Link Clamp 16-4215-00 16-4215-20 1 3/4 - 16 0.38 1.689 0.50 1.78 0.250 0.189 0.157 0.561

110 ft-lb

16-4218-00 16-4218-20 2 - 16 0.50 1.939 0.63 2.03 0.250 0.252 0.188 0.658

150 ft-lb

16-4222-00 16-4222-20 2 1/4 - 16 0.63 2.189 0.75 2.28 0.250 0.341 0.188 0.725

200 ft-lb

TWIN LINK CLAMP LEVER DIMENSIONS

D .005

N .005

SEE DETAIL RIGHT

K .003

RADIUS G

RADIUS U

Q .003

RADIUS T

J .005

ILS916017 REV C

Twin Lever Link Clamp Standard Dimensions (in.)

Link Clamp Model No.*

Model No.

A B C D E

MAX MIN

91-6115-20 16-X215-20 1.18 1.51 0.551 0.472 0.167 0.197 0.197 0.1984 0.1972 0.551 0.118 91-6118-20 16-X218-20 1.48 1.87 0.709 0.551 0.197 0.276 0.197 0.2378 0.2366 0.719 0.157 91-6122-20 16-X222-20 1.76 2.24 0.787 0.709 0.256 0.354 0.236 0.3169 0.3155 0.856 0.079

Link Clamp Model No.*

Model No.

M N P

Q R

MAX MIN

91-6115-20 16-X215-20 91-6118-20 16-X218-20 91-6122-20 16-X222-20

0.2370 0.2362 25 0.280 0.370 0.197 0.451 27 0.197 0.167 0.2764 0.2756 30 0.319 0.453 0.217 0.524 29 0.256 0.197 0.3552 0.3544 25 0.398 0.630 0.335 0.591 25 0.394 0.256

5000 PSI Twin Lever Link Clamp High Pressure Offset Output Curves VEKTEK 5000 PSI INCH TWIN LEVER LINK CLAMP CLAMPING FORCE OUTPU T CURVES

16-X215-20

Non-Usable Range

1000 1200 1400 1600

Clamping Force (LBS) Lever Length "L" (IN)

Operating Cy Pressure Force linder

Min Lever

gth

Len

L = .88

0.88 1.00 1.18 1.30 1.50 1.75 2.25 3.00 "L" (IN)

(PSI) 5000 4500 4000 3500 3000 2500 2000 1500 1000 500

(LBS)

1370 2112 1547 1104 927 732 579 409 284 1.18 1233 1901 1393 994 835 659 521 368 255 1.18 1096 1690 1238 884 742 586 463 327 227 1.00 959 1478 1083 773 649 512 406 286 199 0.88 822 1267 928 663 556 439 348 245 170 0.88 685 1056 774 552 464 366 290 204 142 0.88

L = 1.75 L = 2.25 L = 3.00 L = 1.30 L = 1.50 L = 1.18

L = 1.00

0 200 400 600 800

548 411 274 137

845 619 442 371 293 232 164 113 0.88 634 464 331 278 220 174 123 85 0.88 422 309 221 185 146 116 82 57 0.88 211 155 110 93 73 58 41 28 0.88 3500 4210 5000 5000 5000 5000 5000 5000

Max Operating Pressure (PSI)

1000 2000 3000 4000 5000 Operating Pressure (PSI)

ILS916019-15 REV A

VEKTEK 5000 PSI INCH TWIN LEVER LINK CLAMP CLAMPING FORCE OUTPUT CURVES ILS916019-15 REV A

16-X218-20

Non-Usable Range

Operating Cy Pressure Force - The tables and graphs show the relationship between lever length, operating pressure and clamping force. - The lever lengths shown in red bold are Vektek's available levers for purchase. See page XXXX for details. - The row across the bottom of the table is the maximum operation pressure allowed for the associated lever length. - The column on the right of the table is the minimum lever length allowed at the associated operation pressure. - Using the clamp in the Non-Usable range will damage clamp and void product warranty. Min Lever linder Len gth (PSI) 5000 4500 4000 (LBS) 1.10 1.25 1.48 1.75 2.00 2.50 3.00 4.00 "L" (IN) 1972 3417 2453 1712 1264 1017 732 571 397 1.97 1775 3075 2207 1541 1137 916 659 514 358 1.75 1578 2734 1962 1370 1011 814 585 457 318 1.57 1380 2392 1717 1198 885 712 512 400 278 1.44 Clamping Force (LBS) Lever Length "L" (IN) 1200 1600 2000 2400 L = 1.10 L = 1.25

Non-Usable Range

L = 1.48

3500 3000 2500 2000 1500 1000 500

L = 2.50 L = 3.00 L = 4.00 L = 2.00 L = 1.75

1183 2050 1472 1027 758 610 439 343 238 1.44 986 1709 1226 856 632 509 366 286 199 1.44 789 1367 981 685 506 407 293 229 159 1.44 592 1025 736 514 379 305 220 171 119 1.44

800

394 197

683 491 342 253 203 146 114 79 1.44 342 245 171 126 102 73 57 40 1.44 3350 4100 5000 5000 5000 5000 5000 5000

400

Max Operating Pressure (PSI)

0 1000 2000 3000 4000 5000 Operating Pressure (PSI)

ILS916019-18 REV A ILS916019-18 REV A VEKTEK 5000 PSI INCH TWIN LEVER LINK CLAMP CLAMPING FORCE OUTPUT CURVES

16-X222-20

- The tables and graphs show the relationship between lever length, operating pressure and clamping force. - The lever lengths shown in red bold are Vektek's available levers for purchase. See page XXXX for details. - The row across the bottom of the table is the maximum operation pressure allowed for the associated lever length. - The column on the right of the table is the minimum lever length allowed at the associated operation pressure. - Using the clamp in the Non-Usable range will damage clamp and void product warranty. Operating Cy Min Lever linder Len Force Pr ssur gth (PSI) (LBS) 1.30 1.50 1.73 2.00 2.38 3.00 4.00 5.00 "L" (IN) 5000 3081 4953 3482 2595 1998 1509 1079 739 562 2.29 4500 2773 4458 3133 2335 1798 1358 971 665 505 2.04 4000 2465 3962 2785 2076 1598 1207 863 591 449 1.85 3500 2157 3467 2437 1816 1398 1056 755 517 393 1.75 Non-Usable Range Clamping Force (LBS) Lever Length "L" (IN) 2000 2500 3000 3500 16-X222-20 L = 1.30 L = 1.50

Non-Usable Range

L = 1.73

L = 4.00 L = 5.00 L = 3.00 L = 2.38 L = 2.00

3000 2500 2000 1500 1000 500

1849 2972 2089 1557 1199 905 647 443 337 1.75 1541 2476 1741 1297 999 755 539 369 281 1.75 1233 1981 1393 1038 799 604 431 295 225 1.75 924 1486 1044 778 599 453 324 222 168 1.75

1500

1000

616 308

991 696 519 400 302 216 148 112 1.75 495 348 259 200 151 108 74 56 1.75 3480 4300 5000 5000 5000 5000 5000 5000

500

Max Operating Pressure (PSI)

1000 2000 3000 4000 5000 Operating Pressure (PSI)

ILS916019-22 REV A

- The tables and graphs show the relationship between lever length, operating pressure and clamping force. - The lever lengths shown in red bold are Vektek’s available levers for purchase. See previous page for details. - The row across the bottom of the table is the maximum operation pressure allowed for the associated lever length. - The column on the right of the table is the minimum lever length allowed at the associated operation pressure. - Using the clamp in the Non-Usable range will damage clamp and void product warranty.

NEW SCREW-IN CARTRIDGE MOUNT LINK CLAMP DOUBLE ACTING SINGLE LEVER DESIGN  Patented rotary lug feature delivers 360 degrees of lever/body positioning.  Available in 3 sizes, 1000lb, 1400lb, and 2400lb total clamping force at 5000 PSI.  Cartridge mount body is manifold mount only.  Cartridge mount body minimizes clamp footprint with easy to machine cavity  Maximum clamping force - minimal footprint.  Levers sold separately.

U.S. Patent No. 8,678,362

SPECIFICATIONS

Effective Piston Area (sq. in.)

Vertical Clamping Stroke (in.)**

LEVERS

Oil Capacity (cu. in.)

Maximum Flow Rate*** (cu. in./min.)

Clamping Capacity (lbs)*

Model No.

STANDARD EXTENDED

Extend Extend Retract

Model No.

Double Acting (D/A) Cylinders, actuated hydraulically both directions. 16-4215-00 1,000 0.10 0.274 0.213 0.077 26

91-6115-01 91-6115-02 91-6118-01 91-6118-02 91-6122-01 91-6122-02

16-4218-00 1,400 16-4222-00 2,400

0.12 0.14

0.394 0.616

0.379 0.116 0.715 0.258

45 86

ILS160018 REV A

* Clamp capacities are listed at 5000 PSI maximum operating pressure with a standard length link clamp lever installed. Minimum operating pressure is 500 PSI for double acting. The clamping force is adjustable by varying the hydraulic system pressure. Use of an extended length lever will result in a reduction of clamp force. (Actual force will vary slightly due to mechanical inefficiencies, and friction.) ** Equal to ±3° with standard lever. *** To ensure maximum service life and trouble-free operation, restrict fluid flow to the above flow ratings when clamping. If you are unable to measure flow rates, these devices should be positioned in no less than 1/2 second. These recommendations apply when using the standard lever. When using the optional extended lever or your custom lever, please restrict the flow rates to position the lever in no less than 1 second.

3 CLAMP ANGLE

A THREAD D AG

M CLAMP STROKE N

TOTAL STROKE

ILS160019 REV A

G HEX

For proper sealing, the mating surface must be flat within .002 in. with a maximum 63 µin R a surface finish.

DIMENSIONS (IN)

Model No.

C D E

H J

Double Acting (D/A) Cylinders, actuated hydraulically both directions. 16-4215-00 1 3/4-16 4.29 3.58 1.37 2.87 0.59 2.00 0.47 0.16 1.66 16-4218-00 2-16 5.07 4.11 1.48 3.32 0.74 2.50 0.59 0.19 1.91 16-4222-00 2 1/4-16 5.83 4.79 1.51 3.80 0.97 3.00 0.71 0.20 2.15

Model No.

M N T

AB AD AF

AG AH

Visit our catalog or website for Link Clamp Levers Options

16-4215-00 1.25 0.78 0.92 2.188 1.63 16-4218-00 1.29 0.96 1.11 2.750 2.01 16-4222-00 1.31 1.16 1.34 3.250 2.32

18 19 19

3.10 2.24 1.063 3.64 2.56 1.201 4.19 2.90 1.457

Vektek is... Power Clamping Innovation

Like you, we are a metalworking manufacturer. We understand the

demands of production and profitability. Our engineers strive to implement the latest technology and intelligence into the design of our workholding products. Vektek is known, worldwide, for innovative solutions, the reliability of our products and our extraordinary sales and technical support teams. Team Vektek is here to assist in any way to see that your move to, or improvement of, Precision Power Workholding is easy and cost effective.

and CAD drawings Also available in: • Chinese • Japanese • Korean • Portuguese • Spanish

Troy Estes, President Vektek LLC

1334 E. 6th Avenue Emporia, KS 66801

Be sure to request all of our NEW product brochures! We’ve got some really innovative products that we don’t want you to miss! Learn more - Give us a call: 800-992-0236 sales@vektek.com

Keep your hydraulics secure with our anti-rotation device for Rotating Unions.

Acutal Size 1000# Capacity Work Support

VEKTEK / Creating New Expectations

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8

www.vektek.com

Made with FlippingBook - Online Brochure Maker