INSERTS (mm)
THE BROACHING AND SLOTTING INSERTS REV ® ARE ALL COMPLETELY INTERNALLY PRODUCED, STARTING FROM THE RAW MATERIAL.
Available in both sintered alloys made from micro-powders and carbide. Sintered steel inserts, after a special heat treatment, reach hardnesses of 70/71 HRC while maintaining an extremely high toughness. Carbide inserts are made with a grade of powder that provides toughness to the material. Toughness is essential in slotting operations to withstand the high pressures generated during cutting. All inserts also a surface coating treatment with anti-wear and anti-seize properties to improve their wear resistance. REV ® inserts are sharpened using precise tapering methods, achieving the correct geometries for maximum cutting performance and to eliminate possible collision problems that would hinder the cutting phase. The geometry of REV ® inserts allows for a high number of resharpenings. All these features ensure that REV ® inserts have optimal durability. Inserts with the suffix "SM" perform a 0.2x45° chamfer at the intersection between the hole and the side of the broached slot, leaving the hole free of burrs. For all standard REV ® inserts in the SM version, the chamfer has been calculated considering the diameters and radius depths regulated in UNI 6604. Anything that differs from the standard dimensions in the table will be considered special. REV ® can supply special inserts for specific tolerances, sizes, and geometries very quickly.
(mm)
IN (mm)
L1
L2
L3
L4
L5
L6
IN-12 P9
HM
11,982 11,982 12,018 12,018
13,1 13,1 13,1 13,1 13,1 13,1
14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
18,5 18,5 18,5 18,5 18,5 18,5
6,5
UT-12 UT-12 UT-12 UT-12 UT-12 UT-12
RF-3 RF-3 RF-3 RF-3 RF-3 RF-3 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-4 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5 RF-5
IN-12 P9-SM HM
3,89
IN-12 H7
HM
6,5
IN-12 H7-SM HM IN-12 D10 HM
3,89
12,12
6,5 6,5
IN-12 C11 IN-14 P9
HM HM
12,205 13,982 13,982 14,018 14,018 14,120 14,205 15,982 15,982 16,018 16,018 16,120 16,205 17,982 17,982 18,018 18,018 18,120 18,205 19,978 19,978 20,021 20,021 20,149 20,240 21,978 21,978 22,021 22,021 22,149 22,240 24,978 24,978 25,021 25,021 25,149 25,240
18 18 18 18 18 18 18 18 18 18 18 18 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26
22 22 22 22 22 22 22 22 22 22 22 22 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
7
UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-14/16 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25 UT-18/25
IN-14 P9-SM HM
4,71
IN-14 H7
HM
7
IN-14 H7-SM HM IN-14 D10 HM
4,71
7 7 8
IN-14 C11 IN-16 P9
HM HM
IN-16 P9-SM HM
5,53
IN-16 H7
HM
8
IN-16 H7-SM HM IN-16 D10 HM IN-18 P9** HM IN-18 P9-SM** HM IN-18 H7** HM IN-18 H7-SM** HM IN-16 C11 HM IN-18 D10** HM IN-18 C11** HM IN-20 P9** HM IN-20 P9-SM** HM IN-20 H7** HM IN-20 H7-SM** HM IN-20 D10** HM IN-20 C11** HM IN-22 P9** HM IN-22 P9-SM** HM IN-22 H7** HM IN-22 H7-SM** HM IN-22 D10** HM IN-22 C11** HM IN-25 P9** HM IN-25 P9-SM** HM IN-25 H7** HM IN-25 H7-SM** HM IN-25 D10** HM IN-25 C11** HM
5,53
8 8 9
5,67
9
5,67
9 9
10
6,29
10
6,29
10 10
11
6,79
11
6,79
11 11
12
7,02
12
7,02
12 12
** For these insert sizes we recommend machining in two steps: roughing and finishing.
17
www.revtool.eu
TOOLS AND INSERTS
GENERAL CATALOGUE 2026
Made with FlippingBook - Online Brochure Maker