INSERTS (pollici)
THE BROACHING AND SLOTTING INSERTS REV ® ARE ALL COMPLETELY INTERNALLY PRODUCED, STARTING FROM THE RAW MATERIAL.
Available in both sintered alloys made from micro-powders and carbide. Sintered steel inserts, after a special heat treatment, reach hardnesses of 70/71 HRC while maintaining an extremely high toughness. Carbide inserts are made with a grade of powder that provides toughness to the material. Toughness is essential in slotting operations to withstand the high pressures generated during cutting. All inserts also a surface coating treatment with anti-wear and anti-seize properties to improve their wear resistance. REV ® inserts are sharpened using precise tapering methods, achieving the correct geometries for maximum cutting performance and to eliminate possible collision problems that would hinder the cutting phase. The geometry of REV ® inserts allows for a high number of resharpenings. All these features ensure that REV ® inserts have optimal durability. Inserts with the suffix "SM" perform a 0.2x45° chamfer at the intersection between the hole and the side of the broached slot, leaving the hole free of burrs. For all standard REV ® inserts in the SM version, the chamfer has been calculated considering the diameters and radius depths regulated in UNI 6604. Anything that differs from the standard dimensions in the table will be considered special. REV ® can supply special inserts for specific tolerances, sizes, and geometries very quickly.
(mm)
(pollici) (inches)
IN” (pollici) (inches)
L1
L1
L2
L3
L4
L5
L6
IN-5/16"-D10 HM
8,036
0,3163
0,3968
0,3543
0,2362
0,5314
0,1875
UT-08
RF-2
IN-5/16"-C11 IN-3/8"-P9 IN-3/8"-H7
HM HM HM
8,108
0,3191
0,3968
0,3543
0,2362
0,5314
0,1875
UT-08
RF-2
9,511
0,3744
0,5157
0,5511
0,3937
0,7283
0,2500
UT-10
RF-3
9,540
0,3755
0,5157
0,5511
0,3937
0,7283
0,250
UT-10
RF-3
IN-3/8"-D10 HM
9,623
0,3788
0,5157
0,5511
0,3937
0,7283
0,250
UT-10
RF-3
IN-3/8"-C11 IN-7/16"-P9 IN-7/16"-H7
HM HM HM
9,695
0,3816
0,5157
0,5511
0,3937
0,7283
0,250
UT-10
RF-3
11,094
0,4367
0,5157
0,5511
0,3937
0,7283
0,250
UT-12
RF-3
11,13
0,4382
0,5157
0,5511
0,3937
0,7283
0,250
UT-12
RF-3
IN-7/16"-D10 HM
11,232
0,4422
0,5157
0,5511
0,3937
0,7283
0,250
UT-12
RF-3
IN-7/16"-C11 IN-1/2"-P9 IN-1/2"-H7
HM HM HM
11,318
0,4455
0,5157
0,5511
0,3937
0,7283
0,250
UT-12
RF-3
12,682
0,4992
0,5157
0,5511
0,3937
0,7283
0,300
UT-12
RF-3
12,718
0,5007
0,5157
0,5511
0,3937
0,7283
0,300
UT-12
RF-3
IN-1/2"-D10 HM
12,8200 0,5047
0,5157
0,5511
0,3937
0,7283
0,300
UT-12
RF-3
IN-1/2"-C11
HM
12,9050 0,508
0,5157
0,5511
0,3937
0,7283
0,300
UT-12
RF-3
IN-9/16"-P9 HM
14,27
0,5617
0,7086
0,5511
0,3937
0,8661
0,275
UT-14/16
RF-4
IN-9/16"-H7
HM
14,306
0,5632
0,7086
0,5511
0,3937
0,8661
0,275
UT-14/16
RF-4
IN-9/16"-D10 HM
14,408
0,5672
0,7086
0,5511
0,3937
0,8661
0,275
UT-14/16
RF-4
IN-9/16"-C11 IN-5/8"-P9 IN-5/8"-H7
HM HM HM
14,492
0,5705
0,7086
0,5511
0,3937
0,8661
0,275
UT-14/16
RF-4
15,8570 0,6242 0,7086
0,5511
0,3937
0,8661
0,312
UT-14/16
RF-4
15,8930 0,6257
0,7086
0,5511
0,3937
0,8661
0,312
UT-14/16
RF-4
IN-5/8"-D10 HM
15,9950 0,6297
0,7086
0,5511
0,3937
0,8661
0,312
UT-14/16
RF-4
IN-5/8"-C11
HM
16,080
0,633
0,7086
0,5511
0,3937
0,8661
0,312
UT-14/16
RF-4
IN-3/4"-P9** HM IN-3/4"-H7** HM IN-3/4"-D10** HM IN-3/4"-C11** HM
19,028
0,7491
1,024
0,7086
0,3937
1,181
0,393
UT-18/25
RF-5
19,071
0,7508
1,024
0,7086
0,3937
1,181
0,393
UT-18/25
RF-5
19,199
0,7558
1,024
0,7086
0.3937
1,181
0,393
UT-18/25
RF-5
19,290
0,7594
1,024
0,7086
0,3937
1,181
0,393
UT-18/25
RF-5
** For these insert sizes we recommend machining in two steps: roughing and finishing.
19
www.revtool.eu
TOOLS AND INSERTS
GENERAL CATALOGUE 2026
Made with FlippingBook - Online Brochure Maker