NEW
BD POWER Killer Grid Heater Upgrade Kit (‘07.5-‘24, 6.7L 2500/3500/4500/5500) BD-1041520: $219.95 The Killer Grid Heater Upgrade Kit is purpose-built to address a major flaw in the 6.7L Cummins engine that can result in total engine destruction. The problem lies in the electrical connection to the intake grid heater. When powering the grid heater, 200 amps pass through a small bolt and nut inside the intake and over time is known to deteriorate and eventually arc and break off. This nut drops into the engine, leading to extensive damage to the piston, head, and valves. This kit upgrades that flawed electrical circuit by eliminating the problematic bolt and nut inside the intake while retaining stock functionality of the heater, is cost-effective, and is easy to install. • Eliminates the problematic grid heater bolt and nut that could lead to engine damage • Allows for full heat output with the stock intake grid heater • Easy installation with no modifications or tuning required • Kit includes replacement hardware and gaskets, along with special tools required for the job • Self-locking threads built into the lower busbar which will prevent the connection from backing out and compromising electrical connection
FLEECE INTAKE AND GRID HEATER KIT (‘07.5-’24) FPE-CUMM-IHK-0724: $599.00
Fleece Performance Engineering intake horn and grid heater kit for the 6.7L Cummins offers the most complete kit available to address the OEM grid heater nut failure. The direct replacement intake horn and high-flow intake plate increase overall engine airflow and replace the OEM style grid heater with a robust coil heating element. For our cold weather customers who experience sustained temperatures below 23°F (-5°C), our cold weather kit (FPE-CUMM- IAH-X2) adds an additional 700W heating element – together this combination provides for proven startability down to -31°F (-35°C)! • One kit fits 2007.5-2024 2500/3500/4500/5500 6.7L Cummins engines – the broadest coverage of any kit on the market! We make it easy – no need to worry about being unsure if you’ve selected the right kit for your truck. • No need to hunt down gaskets for the job – we include everything you need in the kit! Gaskets include intake runner, intake horn, throttle valve, EGR valve, and EGR crossover tube gaskets. • Clearly labeled hardware kits make it easy to identify and locate all the necessary parts for the installation. • Labeled electrical connections make installation a breeze – no guessing which end goes where. • No need for proprietary high pressure fuel lines – reuse your OE high pressure fuel lines or install direct replacement aftermarket options that are available nationwide from your favorite aftermarket supplier or OE reseller. • Heater cables and connections incorporate protective boots, eliminating any risk of inadvertent contact with an energized circuit – no exposed connections like other options on the market.
Motor Mount REINFORCEMENTS ‘98.5-‘02, 24V ES_51116G: $67.80 ‘94-‘98, 12V ES_51114G: $79.60 Motor mount inserts sold in Black only. NOTE: These are not replacement bushings, just reinforcements.
HEAVY-DUTY REAR ENGINE/TRANSMISSION POLYURETHANE MOUNT (‘89-‘05, 2500/3500) ‘03-‘05 2500/3500 ‘03-‘05 1500 PB3066: $119.00 NEW! ‘94-‘02 PB2852: $119.00 ‘89-‘93 PB1604: $30.95 pair (‘89-‘93 4x4 only) The add-on cold weather kit provides proven engine startability down to -35° Cesius (-31° F)! Optimized heater design and placement in the intake air stream ensure you get the most efficient heating possible. Compared with other gid heating kits on the market, the Fleece Performance kit achieves the same levels of cold temperature startability with lower wattage and less strain on your grid heater relay. PB2852 shown COLD WEATHER UPGRADE KIT FOR THE FLEECE INTAKE AND GRID HEATER KIT (‘07.5-’24) FPE-CUMM-IAH-X2: $109.99
Polyurethane heavy-duty Engine Mount insertS ‘94-’02 PB2453KIT: $199.95 pair
These are a solid polyurethane mount where the factory ones are rubber with gapped holes in them. These are not inserts that fit inside the stock rubber, but a replacement for the whole rubber mount. To install, remove the old rubber from the engine mount and replace with these.
Polyurethane heavy-duty Engine Mounts (‘89-’93) PB2710: $169.00 pair These are solid polyurethane inserts with an internal locking system where the factory ones have an external safety lock. Features stainless steel hardware. Fits all Dodge pickups equipped with the Cummins engine from ‘89-‘93. Mounts: 3” x 3-1/2” and 1-3/4” thick.
This heavy duty, polyurethane bushing is a direct replacement for the stock mount. Fits in the same location, easy to install.
Order 770-886-2500 or genosgarage.com 59
Product prices subject to change without notice.
Made with FlippingBook Ebook Creator