PAPERmaking! Vol12 Nr2 2026

Coatings 2026 , 16 , 299

14of 25

single-coated reference samples (RSA1 and RSB1) and the multilayered samples with comparable coat weights (A6, B6 and MB6) clearly shows that the multilayer strategy produced significantly lower filtered Sa values (i.e., lower roughness). This observation is consistent with the Bendtsen roughness for the corresponding samples in Table 4, where the multilayer approach also yielded lower roughness values (although the differences were not always statistically significant). The total surface volume ( V s ) of the coated paperboards (Table 5) did not differ substantially between samples, once again indicating a high degree of contour coating. Additional evidence for contour coating is provided by the rather constant Sc/Sv ratio, which remained between 9 and 12 for BASE and all coated samples. The wet volume ( V wet ) applied after metering at each coating step can be calculated from the increase in coat weight, provided that the density and dry solid content of the wet coating dispersion are known. The approximate density of the coating dispersion was calculated based on the assumption of ideal mixing [80]. The densities of pure starch, PEG, water, and bentonite were set to 1.4985 g cm − 3 [80], 1.126 g cm − 3 , 0.995gcm − 3 , and 2.35 g cm − 3 [81], respectively. The estimated resulting density of the coating dispersion and the aqueous phase of the dispersion were 1.07 g cm − 3 and 1.04 g cm − 3 , respectively. Although the assumption of ideal mixing deviates from real conditions, it provides a sufficiently accurate approximation for estimating the wet volume applied at each coating step. The real density values are supposed to be higher than the calculated ones. A fundamental requirement for fibre coverage is that the wet volume of the coating dispersion fills the surface volume between large-scale height variations caused by fibre flocs. Table 6 shows V s and V wet for selected coated samples. For the thin multilayered samples (A1, A6, B1, B6 and MB6), V wet was substantially smaller than V s , indicating that compression of the substrate beneath the metering element was required to obtain good fibre coverage and a uniform coating layer. Increased compression beneath the metering element has previously been shown to promote more uniform coating [82].

Table6. Total surface volume ( V s ) of the paperboard entering the coater, incremental coat weight and the wet volume of coating dispersion applied after metering ( V wet ) in the production of coated samples.

Paperboard Entering theCoater

V s (cm 3 m − 2 ) 11.0 ± 0.6 9.3 ± 1.3 11.0 ± 0.6 9.7 ± 1.0 9.7 ± 1.0 11.0 ± 0.6 11.0 ± 0.6 11.0 ± 0.6 10.22 ± 0.35 11.02 ± 0.65

Incremental Coat Weight (gm − 2 )

V wet (cm 3 m − 2 )

Sample Name

A1 A6 B1 B6

BASE

1.5 0.5 1.4

7.2 2.4 6.7 2.1 2.1

A5

BASE

B5 B5

0.45 0.45

MB6 RSA1 RSB1 RDA1 RDA2 RDB1

BASE BASE BASE RDA1 BASE

5.4 5.4 3.7 3.1 3.9

25.8 25.8 17.7 14.8 18.6

For the thick single-coated reference samples (RSA1 and RSB1), V wet was substan- tially greater than V s , indicating that, in principle, fibre coverage could have been achieved without compressing the substrate. For the reference samples, RDA1, RDA2 andRDB1, V wet was just slightly higher than V s . However, the optical surface profilome- try results also clearly indicated a contour-type coating for the reference samples. This suggests that the substrates were compressed beneath the metering element during the reference trials as well.

https://doi.org/10.3390/coatings16030299

Made with FlippingBook Online newsletter maker