Trex Select® Classic Railing Install Instructions

Complete Trex Select Classic railing installation guide including step-by-step instructions.

TREX SELECT ® CLASSIC COMPOSITE HORIZONTAL RAILING Installation Instructions

Notes: » TREX SELECT CLASSIC RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED. » ALL TREX SELECT CLASSIC RAIL LENGTHS ARE MANUFACTURED AT CLEAR SPAN; 72" FOR 6' CLEAR SPAN, AND 96" FOR 8' CLEAR SPAN. » RAILINGS ARE DESIGNED TO BE SLIGHTLY LONGER THAN REQUIRED TO ALLOW FOR VERY SLIGHT PLAY IN POST PLACEMENT - SOME MINIMAL TRIMMING MAY BE REQUIRED. ALWAYS MEASURE FIRST. » USE STANDARD DRILL WHEN INSTALLING BRACKETS TO POSTS AND BRACKETS TO RAILS. DO NOT USE IMPACT DRIVER. » IF INSTALLING RAILING OVER 6', THE TREX ALUMINUM RAIL STIFFENER MUST BE USED TO MEET CODE REQUIREMENTS.

IMPORTANT–IF INSTALLING TREX LIGHTING, SCAN QR CODE TO OBTAIN RAILING & LIGHTING INSTRUCTIONS / DO NOT USE INSTRUCTIONS BELOW. FAILURE TO DO THIS WILL RESULT IN IMPROPER RAILING AND LIGHTING INSTALLATION!

Care and Cleaning Maintaining the appearance of your Select Classic railing is important. Occasional washing is recommended. Over time your railing may show signs of weathering as a result of exposure to the elements. The frequency of cleaning will depend on the environment and exposure to various types of elements. » Clean railing with standard cleaning vinegar or mild soap and water. » For more detailed cleaning recommendations, please refer to the Trex Railing Care and Cleaning guide found on www.trex.com.

PARTS

F *

DETERMINING BALUSTERS NEEDED

Per 6 ' Section

Per 8 ' Section

Baluster Type

H **

Round Aluminum Baluster (Horizontal Application)

CODE APPROVED APPLICATIONS

G *

B E

6' Railing 8' Railing

< 30" height decking

Yes

IRC Compliant

Yes

Yes*

IBC Compliant

*TREX SELECT 8' ALUMINUM RAIL STIFFENER (sku SELALRAILSTIFFENER) MUST ALSO BE USED. Sold separately.

A. Select Classic top rail B. Select Classic bottom rail C. Brackets D. Balusters E. Adjustable foot block

NOTES: » E nsure pressure-treated posts are installed at proper heights. If installing 42" (1067 mm) railing, use longer post sleeves and measure accordingly to ensure a proper cut. DO NOT CUT TO ACTUAL 42" LENGTH WITHOUT CONFIRMING WHAT STYLE OF RAILING YOU ARE INSTALLING. » *See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing.

F. Post sleeve cap* G. Post sleeve skirt* H. P ost sleeve**

> Trex All-in-One post sleeve > 4 x 4 post sleeve > 6 x 6 post sleeve I. Trex Decking J. Trex Fascia K. Code-approved Wood Joist - 2 x 8 L. Code-approved Wood Rim Joist - 2 x 8 or Larger

Screws Supplied with RSB C1.W ood screw for attachment of RSB to wood post/composite sleeve C2.Self-drilling screw for attachment of RSB to rail

* Item not included in the Select railing kits. Note when using the Select post sleeve, the cap and skirt are included with this post sleeve. ** All post sleeves are designed to fit over 4 x 4 pressure-treated post.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

TREX SELECT ® CLASSIC COMPOSITE HORIZONTAL RAILING Installation Instructions

RAILING CONFIGURATIONS Note: See specific installation instructions for attachment of Trex Post Mounts or Trex Joist Mount Posts prior to installing any railing.

Standard Rail

Cutting post sleeves is NOT required. A. P ost Sleeve (see page 1 for approved post sleeves) > For use with pressure-treated post, Trex Post Mount, or Trex Joist Mount Post (INSIDE MOUNT ONLY) B. Select top rail C. Select bottom rail D. Aluminum balusters (must also use horizontal baluster spacer). See page 3 for “How to Install Standard Horizontal Railing”.

Continuous (Over the Post) Cocktail Rail

POST SLEEVES WILL NEED TO BE CUT

Post sleeves WILL NEED TO BE CUT. A. P ressure-treated post with Tr x post sleeve NOTE: » Only for use with Trex All-in-One Post sleeve or 4 x 4 post sleeve. » Trex post mounts or joist mount posts cannot be used. B. Trex board (1 x 6 or 2 x 6). NOTES: » Enhance board cannot be used. » Top boards will need to be cut to fit each rail span. C. Select top rail D. Select bottom rail E. Aluminum balusters (must also use horizontal baluster spacer). See page 5 for “How to Install Continuous (Over the Post) Cocktail Railing”.

Post-to-Post Cocktail Rail

Cutting post sleeves is NOT required. A. Post Sleeve (see page 1 for approved post sleeves) > For use with pressure-treated post, Trex Post Mount, or Trex Joist Mount Post (INSIDE MOUNT ONLY) B. Trex 1 x 4 board C. Select top rail D. Select bottom rail E. Aluminum balusters (must also use horizontal baluster spacer). See page 7 for “How to Install Post-to-Post Cocktail Railing”.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

HOW TO INSTALL STANDARD HORIZONTAL RAILING TREX SELECT ®

Cutting Railings 3a.Position bottom and

top rails between posts, ensuring baluster holes

are lined up and spaced evenly.

3b.Also allo w for a

1-9/16" (40 mm)

minimum of 1-9/16" (40 mm) on each end of rail for bracket placement AND baluster clearance. Mark rails at intersection of rail and post.

Read all instructions BEFORE installation.

Important: Post sleeves are NO T to be cut for this design style.

Installing Pressure-Treated Posts 1. PLEASE REFER TO LOCAL BUILDING CODE REQUIREMENTS PRIOR TO ATTACHING PRESSURE TREATED POSTS. » P osts are to be installed 6' or 8' clear span to accommodate appropriate railing length. NOTE: Smaller spans are allowed. Installing Post Sleeve Skirts and Post Sleeves 2a. When using All-in-One post sleeve or 6 x 6 2a

IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: » Refer to detailed instructions (Trex Select rail instructions) included with foot block prior to installation of railing section as these include other required steps for proper installation.

Attaching Foot Block to Bottom Rail and Adding Weep Holes 4a. Invert the bottom rail. Center and drill a hole using a 3/16" (5 mm) drill bit. This will be location for foot block attachment (to be installed last).

post sleeve, slide one- piece skirt over post and down to rest on decking surface. Slide post sleeve over post and position inside post sleeve skirt.

2b. W hen using the

4 x 4 post sleeve and two-piece skirt, slide post sleeveover post and down to rest on decking surface. Snap two piece skirt over post sleeve.

4b. Keeping bottom rail inverted, use same drill bit, center and drill weep holes through bottom rail at 4 evenly spanned locations to allow for water drainage.

NOTE: Shims can be used to plumb post sleeves.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

TREX SELECT ® CLASSIC COMPOSITE HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL STANDARD HORIZONTAL RAILING/ CONTINUED

Attaching Brackets to Rails 5a. Position brackets on each end of TOP RAIL on the same side as baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (C2).

Top Rail

NOTE: For ease of bracket attachment place rail against stationary flat vertical surface along with bracket.

6c. Attach top rail to balusters, feeding each baluster into required slots. Start on one end and work towards the other. 6d.To help temporarily secure the railing section together, place a ratchet strap around the top and bottom rail and tighten until snug. DO NOT OVERTIGHTEN AS YOU CAN BEND THE RAILING.

5b.Position brackets on

Bottom Rail

each end of BOTTOM RAIL on the OPPOSITE SIDE of the baluster holes. Attach brackets using three #8-18 x 1" self-drilling screws (C2) .

Installing Railing Section to Posts

NOTE: For ease of bracket attachment place rail against stationary flat vertical surface along with bracket.

Assembling Railing Section

3-3/4" (95 mm)

7a.Using scrap material (i.e. 2 x 4's, decking boards, etc.) cut at least three support blocks at 3-3/4 " (95 mm) in height. Place one each on decking surface beside each post and one near center of span. 7b.Lift secured railing section up, and CENTER this section in between the spanned posts on pre- positioned support blocks. NOTE: To help stabilize railing section use a quick-grip clamp (or other type of clamp) and clamp the first baluster to post sleeve. DO NOT OVERTIGHTEN CLAMP.

6a.On a clean flat surface, lay bottom railing on its side. Make sure to allow enough room for installation of balusters and top rail. Place a scrap piece of 1 " (25 mm) decking board running parallel to bottom rail for support when installing balusters. 6b. Insert balusters into bottom rail slots until balusters are fully seated.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

HOW TO INSTALL STANDARD HORIZONTAL RAILING/ CONTINUED TREX SELECT ®

Attaching Post Caps and Installing Foot Block 8. Secure post caps with silicone or PVC adhesive (apply adhesive on the inside self-centering/ corner tabs). Attach Foot Block per Foot Block instructions.

NOTE: Clean up any excess adhesive before it dries.

7c. Install both bottom and top brackets on each side to post using two #9-16 x 2" wood screws (C1). If using a 6 x 6 post sleeve use two #9-16 x 2 1/2" screws (not provided) .

NOTE: Screws go in at slight angle.

IMPORTANT NOTE: SET DRILL TO LOW SPEED AND LOW CLUTCH SETTING WHEN INSTALLING THESE SCREWS. DO NOT USE IMPACT DRIVER.

HOW TO INSTALL CONTINUOUS (OVER THE POST) COCKTAIL RAILING

Cutting Post and Post Sleeve 2. M ark and cut post and post sleeve measuring from deck surface: » 36-1/8" (918 mm) for 36" (914 mm) height. » 42-1/8" (1070 mm) for 42" (1067 mm) height.

Important: 6 x 6 post sleeve cannot be used. Trex Post Mounts or Joist Mount Posts cannot be used.

36-1/8" (918 mm) or 42-1/8" (1070 mm)

3. Cutting Railings

See instructions on page 3.

4. Attaching Foot Block to Bottom Railing See instructions on page 3.

1. Installing Pressure-Treated Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 3.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

TREX SELECT ® CLASSIC COMPOSITE HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL CONTINUOUS (OVER THE POST) COCKTAIL RAILING/ CONTINUED

Cutting Top Board

8. S ecure top board to top rail with 3/4" screws provided approx. every 16" on center. Screws are to be installed inside of the baluster holes into the decking board. DO NOT overtighten.

NOTES: » If installing in weather below 40°F (4.5°C), leave 1/8" (3 mm) gap between top boards. » Top boards can overhang end of last post maximum 1/2" (13 mm).

NOTES: » A long drill bit will be required to fit inside the baluster holes. » If installing 8’ rail section and using Aluminum Rail Stiffener, predrilling will be required through the stiffener.

9. Attaching Brackets to Rails See instructions on page 4. 10. A ssembling Railing Sections See instructions on page 4. 11. Installing Railing Sections to Posts See instructions on page 4.

5. Cut top boards to appropriate length of railing span, remembering to include extra space on each side of the board to allow for attachment to the post. Decking boards must cover 1/2 of the pressure-treated post to allow this to be fastened later.

12. Attaching Top Board to Posts Attach top board on each post with Trex recommended composite screws (quantity of 2 per each board end). 13. Installing Foot Block Install foot block per detailed instructions.

6. Place inverted top board (top side of

board face down) on clean, flat surface.

Top Board Termination

Attaching Top Board to Top Rail 7. Place inverted top

rail (orient properly so baluster holes are shown top side up), on the top board, centered in both directions to allow final attachment to post.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

HOW TO INSTALL POST-TO-POST COCKTAIL RAILING TREX SELECT ®

6. Place inverted top (orient properly so baluster holes are shown top side up) on 1 x 4. 7. Secure 1 x 4 to top rail with 3/4" screw provided approximately every 16" on center. Screws are to be installed inside of the baluster holes into the decking board. NOTES: » DO NOT overtighten. Note that a long drill bit will be required to fit inside the baluster holes. » If installing 8' rail section and using Aluminum Rail Stiffener, predrilling will be required through the stiffener.

1. Installing Pressure-Treated Posts, Post Sleeve Skirts and Post Sleeves See instructions on page 3.

2. Attaching Foot Block to Bottom Railing See instructions on page 3.

3. Cutting Railings

See instructions on page 3.

Cutting 1 x 4

8. Attaching Brackets to Rails See instructions on page 4. 9. Assembling Railing Sections See instructions on page 4. 10. Installing Railing Sections to Posts See instructions on page 4.

11. Attaching 1 x 4 to Posts P re-drill a pilot hole and toenail 2-1/2"

4. Cut 1 x 4 to same length of the inverted top rail.

(64 mm) composite screw (not provided) at each end of 1 x 4 into post on back side of rail (side not facing decking).

Attaching 1 x 4 to Top Rail 5. Place inverted 1 x 4 (top side face down) on clean, flat surface.

12. Attaching Post Caps and Installing Foot Block Secure post caps with silicone or PVC adhesive(apply adhesive on the inside self- centering/corner tabs). Attach Foot Block per Foot Block instructions.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

TREX SELECT ® CLASSIC COMPOSITE HORIZONTAL RAILING Installation Instructions

HOW TO INSTALL ON-AN-ANGLE RAILING

NOTE: Brackets are designed to be installed up to a 45° angle.

Both 4 x 4 or 6 x 6 post sleeves work well for angles up to 45 degrees. Bottom rail brackets may need to be slightly offset to one side in order to fit

4 x 4 OR 6 x 6 Post Sleeve

properly to hold rail in place. Before attaching bracket to rail, measure and mark to ensure bottom rail remains parallel to upper rail.

4 x 4 Post Sleeve

6 x 6 Post Sleeve

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCHZ-0626

TREX SELECT ® CLASSIC COMPOSITE STAIR RAILING Installation Instructions

Notes: » TREX SELECT CLASSIC RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED. » POST TO POST SPAN WILL BE LESS THAN 6' OR 8'. PRIOR TO POST INSTALLATION, CALCULATE POST TO POST SPAN USING A MAXIMUM RAIL LENGTH REQUIRED AND THE ANGLE (32°-37°) AT WHICH THE RAILS WILL BE INSTALLED. DO NOT INSTALL STAIR POSTS AT 6' OR 8' SPAN, AS THE STAIR RAILING WILL BE TOO SHORT. » USE STANDARD DRILL WHEN INSTALLING BRACKETS TO POSTS AND BRACKETS TO RAILS. DO NOT USE IMPACT DRIVER. » IF INSTALLING RAILING OVER 6', THE TREX ALUMINUM RAIL STIFFENER MUST BE USED TO MEET CODE REQUIREMENTS.

IMPORTANT–IF INSTALLING TREX LIGHTING, SCAN QR CODE TO OBTAIN RAILING & LIGHTING INSTRUCTIONS / DO NOT USE INSTRUCTIONS BELOW. FAILURE TO DO THIS WILL RESULT

IN IMPROPER RAILING AND LIGHTING INSTALLATION!

Care and Cleaning Maintaining the appearance of your Trex Select Classic railing is important. Occasional washing is recommended. Over time your railing may show signs of weathering as a result of exposure to the elements. The frequency of cleaning will depend on the environment and exposure to various types of elements. » Clean railing with standard cleaning vinegar or mild soap and water. » For more detailed cleaning recommendations, please refer to the Trex Railing Care and Cleaning guide found on www.trex.com.

E *

PARTS

DETERMINING BALUSTERS NEEDED

Per 6 ' Section

Per 8 ' Section

Baluster Type

Round Aluminum Baluster(Stair Application)

NOTES: » In most cases, a post and post sleeve longer than 39" (991 mm) will be needed on the lower section of stair rail to accommodate stair angle. » Make sure top and bottom posts for stairs are installed at nose of each tread. » Ensure pressure-treated posts are installed at proper heights so when post sleeves are installed , both the PT post and post sleeve are flush at top. » *See specific installation instructions for attachment of Trex post mounts or Trex Joist Mount Posts prior to installing any railing. » If installing stair railing over 6', Trex Select 8' ALUMINUM RAIL STIFFENER (sku SELALRAILSTIFFENER) MUST ALSO BE USED. Sold separately. Screws Supplied with Brackets C1. W ood screw for attachment of bracket to wood post/composite sleeve C2. S elf-drilling rail screw for attachment of railing to bracket C1 C2

G **

F *

A. Select Classic Stair Top Rail B. Select Classic Stair Bottom Rail C. Brackets

D. Round Balusters E. Post sleeve cap* F. Post sleeve skirt* G. Post sleeve**

> Trex All-in-One Post Sleeve > 4 x 4 post sleeve > 6 x 6 post sleeve H. Adjustable foot block (quantity of one is required for all railing span lengths) * Item not included in the Select railing kits. ** A ll post sleeves are designed to fit over 4 x 4 pressure-treated post.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

TREX SELECT ® CLASSIC COMPOSITE STAIR RAILING Installation Instructions

STAIR RAILING CONFIGURATIONS Note: See specific installation instructions for attachment of Trex Post Mounts or Trex Joist Mount Posts prior to installing any railing. Standard

D. Aluminum balusters (must also use stair baluster spacer). See page 3 for “How to Install Standard Stair Railing”.

Continuous (Over the Post) Cocktail Rail

Post sleeves WILL NEED TO BE CUT. A. Pressure-treated post with Trex post sleeve NOTE: » Only for use with Trex All-in-One Post sleeve or 4 x 4 post sleeve. » Trex post mounts or joist mount posts cannot be used. B. Trex board (1 x 6 or 2 x 6). NOTE: Enhance board cannot be used. C. Select Stair top rail D. Select Stair bottom rail E. Aluminum balusters (must also use stair baluster spacer). See page 6 for “How to Install Continuous (Over the Post) Cocktail Railing”.

POST SLEEVES WILL NEED TO BE CUT

NOTE: Additional pan head screws will need to be purchased–see detailed instructions.

Post-to-Post Cocktail Rail

E. Aluminum balusters (must also use stair baluster spacer). See page 7 for “How to Install Post-to-Post Cocktail Railing”.

NOTE: Additional pan head screws will need to be purchased - see detailed instructions.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

HOW TO INSTALL STANDARD STAIR RAILING TREX SELECT ®

Measuring and Cutting Bottom Rail 3. P lace a 1" deckboard on the nose of the stair tread.

1. Installing Pressure-Treated Posts » PLEASE REFER TO LOCAL BUILDING CODE REQUIREMENTS PRIOR TO ATTACHING PRESSURE TREATED POSTS. » PRESSURE TREATED POSTS MUST BE INSTALLED ON INSIDE OF STAIR STRINGER AND AT NOSE OF STAIR TREAD. » POST TO POST SPAN WILL BE LESS THAN 6' OR 8'. PRIOR TO INSTALLING POSTS CALCULATE POST TO POST SPAN USING A MAXIMUM RAIL LENGTH REQUIRED AND THE ANGLE (32°-37°) AT WHICH THE RAILS WILL BE INSTALLED. DO NOT INSTALL STAIR POSTS AT 6' OR 8' SPAN, AS STAIR RAILINGS WILL THEN BE TOO SHORT. » Post sleeve longer than 39" (991 mm) will be needed on the lower section of stair rail to accommodate stair angle.

4. Set railing on top of deckboard, making sure baluster holes are vertically aligned and mark line at each intersection. When measuring, cut equal lengths from each side of railing allowing a minimum of 2 " (51 mm) on each end from the last baluster hole to the end of the rail. This will ensure proper baluster and bracket placement and equal spacing of balusters per each railing section. IMPORTANT NOTE REGARDING FOOT BLOCK INSTALLATION: » R efer to detailed instructions (Trex Select rail instructions) included with foot block prior to installation of

Installing Post Sleeve Skirts and Post Sleeves 2a.When using the All-in- One post sleeve or 6 x 6 post sleeve, slide one- piece skirt over post and down to rest on decking surface. Slide post sleeve over post and position inside post sleeve skirt. 2b. If using the 4 x4 post sleeve, slide post sleeve over post and down to rest on decking surface. Snap two piece skirt over post sleeve. Note: Shims can be used to plumb post sleeves.

railing section as these include other required steps for proper installation.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

TREX SELECT ® CLASSIC COMPOSITE STAIR RAILING Installation Instructions

HOW TO INSTALL STANDARD STAIR RAILING/ CONTINUED TREX SELECT ®

Marking Location for Foot Block to Bottom Rail

Attachment of Bottom Rail to Post

NOTE: For attachment of brackets to posts, use at least a 3" long drill bit or extension so as to not damage sides of rails when installing.

TIP: Pre-drill prior to screw installation using a 7/64" drill bit

4" (10 cm)

8a.K eeping deck board on stair treads, center bottom rail between posts and attach

bottom rail stair bracket to upper post using two #9-16 x 3" wood screws (C1).

5. Mark approximate location for foot block, allowing a measurement of 4" maximum. Invert the bottom rail, and at marked location drill a hole using a 3/16" drill bit in the center of the channel. Foot block assembly will be installed last.

8b.A ttach bottom stair rail stair bracket to lower post using two

Attaching Brackets to Bottom Rail 6. Snap the top stair adaptor bracket (labeled TOP) to the standard bracket. Repeat for remaining bottom bracket. 6

#9-16 x 3" wood screws (C1), deck board can now be removed.

IMPORTANT NOTE: SET DRILL TO LOW SPEED AND LOW CLUTCH SETTING WHEN INSTALLING THESE SCREWS. DO NOT USE IMPACT DRIVER.

TIP: Use a dap of super glue when snapping bracket together. This will help stabilize bracket when installing.

Measuring and Cutting Top Stair Rail

9. P lace two balusters into lower stair rail at each end closest to the post. 10. P osition top stair rail onto balusters, ensuring balusters are fully seated in rail (position to side of post), and ENSURE balusters are spaced evenly AND parallel with posts.

7. On the BOTTOM RAIL, attach the assembled bottom stair brackets to the OPPOSITE SIDE of the baluster holes. Attach both brackets using three #8-18x1" selfdrilling screws (C2).

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

HOW TO INSTALL STANDARD STAIR RAILING/ CONTINUED TREX SELECT ®

Installing Balusters 15. Slide remaining

balusters into bottom rail until balusters are fully seated.

Attachment of Top Rail to Post 16. P lace top rail onto

balusters, allowing the top rail to rest on the surface of the balusters.

11. M ark top stair rail at post intersections.

NOTE: For attachment of brackets to posts, use at least a 3" long drill bit or extension so as to not damage sides of rails when installing.

12. R emove rail, and cut along the marks.

NOTE: Verify the height of the railing before installing rail to post to ensure this meets proper height requirements for stairs.

TIP: Pre-drill prior to screw installation using a 7/64" drill bit

17b

17a

Attaching Brackets on Top Stair Rail

13. S nap the top stair

adaptor bracket (labeled TOP) to the standard bracket. Repeat for remaining bracket.

17a.Attach top stair rail bracket to upper post using two #9-16 x 3 " screws (C1). 17b.Attach top stair rail bracket to lower post using two #9-16 x 3 " screws (C1). IMPORTANT NOTE: SET DRILL TO LOW SPEED AND LOW CLUTCH SETTING WHEN INSTALLING THESE SCREWS. DO NOT USE IMPACT DRIVER.

TIP: Use a dap of super glue when snapping bracket together. This will help stabilize bracket when installing.

Attaching Post Caps and Installing Foot Block 18. S ecure post caps with silicone or PVC adhesive (apply adhesive on the

inside self-centering/ corner tabs). Attach Foot Block per Foot Block instructions.

14. O n the TOP RAIL, attach the assembled stair brackets to the side WITH the baluster holes. Attach both brackets using three #8-18x1" self-drilling screws (C2).

NOTE: Clean up any excess adhesive before it dries.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

TREX SELECT ® CLASSIC COMPOSITE STAIR RAILING Installation Instructions

HOW TO INSTALL CONTINUOUS (OVER THE POST) COCKTAIL STAIR RAILING

Cutting Post and Post Sleeve 8. C ut lower post/post

IMPORTANT NOTES: » 6 x 6 post sleeve cannot be used. Trex post mounts or joist mount posts cannot be used. Cutting post and post sleeve only apply to the Continuous (Over the Post) Cocktail railing. » THE TOP BOARD USED WILL NEED TO TERMINATE AT THE UPPER STAIR POST AS SHOWN BELOW. THE TOP BOARD WILL HAVE TO BE TOENAILED INTO THE SIDE OF THE POST IN THESE AREAS USING 2 APPROPRIATE COMPOSITE DECKING SCREWS – PRE-DRILLING IS RECOMMENDED.

sleeve at proper angle so this is flush with the top of the top rail.

Top stair rail

Post

9. Attaching Brackets on Top Stair Rail See instructions on page 5.

Measuring and Cutting Top Board

1. Installing Pressure-Treated Posts See instructions on page 3 .(See note above in regards to not cutting post/post sleeve). 2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 3.

3. Measuring and Cutting Bottom Stair Rail See instructions on page 4.

10. Measure accordingly and cut top boards to appropriate length of railing span also allowing for additional material that will be installed over the lower stair rail post.

4. Marking Location for Foot Block to Bottom Rail See instructions on page 4.

5. Attaching Brackets to Bottom Rail See instructions on page 4. 6. Attachment of Bottom Rail to Post See instructions on page 4. 7. Measuring and Cutting Top Stair Rail See instructions on page 4.

Attaching Top Board to Top Stair Rail 11. Place inverted top board (place top side of board down) on clean, flat surface. 11

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

HOW TO INSTALL CONTINUOUS (OVER THE POST) COCKTAIL STAIR RAILING/ CONTINUED

Attaching Top Board to Top Rail 12.Place inverted top rail (orient properly so baluster holes are shown top side up), on the top board so the angled cuts will align properly along with centering the top rail on the board. 13. Secure top board to top rail with 3/4" screws provided approximately every 16" on center.

See instructions on page 5.

Attachment of Top Board to Post 16. Attach top board to lower post with Trex-recommended composite screws (quantity of 2 per each post/board end).

17. W here top board

terminates at upper post, PREDRILL and toenail two approved composite deck screws as shown into post, being careful to avoid hitting stair bracket. Installation of Foot Block 18. Attach foot block per foot block instructions.

Screws are to be installed inside of the baluster holes into the board.

NOTES: » DO NOT overtighten. » Note that a long drill bit will be required to fit inside the baluster holes. » If installing 8' rail section and using the Aluminum Rail Stiffener, predrilling will be required through the stiffener.

14. Installing Balusters

See instructions on page 5.

15. Attachment of Top Rail to Post

HOW TO INSTALL POST-TO-POST COCKTAIL STAIR RAILING

1. Installing Pressure-Treated Posts See instructions on page 3 2. Installing Post Sleeve Skirts and Post Sleeves See instructions on page 3. 3. Measuring and Cutting Bottom Stair Rail See instructions on page 4. 4. Marking Location for Foot Block to Bottom Rail See instructions on page 4. 5. Attaching Brackets to Bottom Rail See instructions on page 4.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

TREX SELECT ® CLASSIC COMPOSITE STAIR RAILING Installation Instructions

HOW TO INSTALL POST-TO-POST COCKTAIL STAIR RAILING/ CONTINUED

6. Attachment of Bottom Rail to Post See instructions on page 4. 7. Measuring and Cutting Top Stair Rail See instructions on page 4.

12. Secure 1 x 4 to top rail with 3/4" screw

provided approximately every 16" on center. Screws are to be installed inside of the baluster holes into the 1 x 4.

Measuring and Cutting 1 x 4

NOTES: » DO NOT overtighten. » Note that a long drill bit will be required to fit inside the baluster holes. » If installing 8' rail section and using Aluminum Rail Stiffener, predrilling will be required through the stiffener.

13. Installing Balusters

See instructions on page 5.

14. Attachment of Top Rail to Post See instructions on page 5.

8. U sing the cut top rail as template, cut 1 x 4 at same angle and length of the top rail.

9. Attaching Brackets on Top Stair Rail See instructions on page 5.

Attaching 1 x 4 to Post

Attaching 1 x 4 to Top Rail 10. Place inverted 1 x 4

(top side face down) on clean, flat surface.

11. Place inverted top

15. Pre-drill a pilot hole and toenail 2-1/2" (6.4 cm) composite deck screw (not provided) at each end of 1 x 4 into post on outside of stair rail (side not facing decking).

rail (orient properly so baluster holes are shown top side up) on 1 x 4.

16. A ttaching Post Caps and Installing Foot Block See instructions on page 5.

Have Questions? 1–800–BUY–TREX

NOTE: Construction methods are always improving. Please ensure you have the most up-to-date installation instructions by visiting: trex.com

SCST-0626

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16

www.trex.com

Made with FlippingBook interactive PDF creator