PAPERmaking! Vol12 Nr2 2026

Coatings 2026 , 16 , 299

2of 25

The hydrophilic nature of the cellulose fibre and the porous structure of paper and paperboard necessitate additional processing steps to enhance barrier properties. One such step is the application of coatings to render the surface layer nearly impermeable to the target penetrant [2]. To achieve effective barriers against gas and liquid penetration, the coating must be as free from defects as possible. The interactions between the applied water-based barrier coatings (WBBCs) and the paper or paperboard substrate are of high im- portance. Water absorptiveness, density, roughness, and surface structure of the uncoated substrate significantly affect the final properties of the coated product [6–11]. The impor- tance of a smooth and dense substrate for a high-speed barrier coating was demonstrated by Vähä-Nissi et al. [11]. An oxygen transmission rate (OTR) as low as 0.02 cm 3 m − 2 day − 1 bar − 1 was found in pilot trials where styrene–butadiene aqueous dispersions, modified with platy fillers and wax, were applied onto smooth high-density papers surface-sized with carboxymethyl cellulose (CMC). However, high-density papers (greaseproof papers) with air permeance below 0.3 nm Pa − 1 s − 1 still exhibit oxygen transmission rates that are too high for them to function as oxygen barrier materials without additional coating [12]. To reduce water absorption and enhance water resistance, hydrophobic sizing agents are added to the fibre furnish during papermaking, a process known as inter- nal sizing [13–18]. Furthermore, polymer dispersions or solutions are often applied to the surface of paper and paperboard to control surface porosity, improve printability and print quality, enhance surface finish, and increase the surface or internal strength. This process is referred to as surface sizing. Paperboard grades are often surface-sized prior to coating to enhance coating hold-out and surface coverage, thereby preventing the penetration of the coating into the baseboard [19,20]. Surface sizes may also include hydrophobic agents and mineral pigments, and the distinction between surface sizing and coating is not always clear-cut. The predominant techniques for producing barrier-coated paper and paperboard are water-based coating and extrusion coating. In water-based coating processes, both polymer dispersions and water-soluble polymers are employed. Notably, WBBC formulations frequently utilise synthetic latex dispersions, which may include mineral fillers and are typically applied at relatively high solids content [11,21–23]. Poly(vinyl alcohol) (PVOH) and modified starches are water-soluble polymers commonly used in water-based solutions for surface sizing and as co-binders in coating applications [1,24]. Films and coatings based on starch and PVOH have also demonstrated suitable barrier properties for certain applications [25–29]. However, the gas permeability of starch films increases dramatically with increasing ambient humidity [30]. Water-based biopolymer coatings are increasingly replacing petroleum-based coatings in some packaging applications because of their ability to maintain the recyclability and compostability of paper and paperboard substrates [2]. Historically, the development of water-based paper coating technology has been driven by demands to improve print quality and aesthetical properties such as gloss and brightness [31]. Aesthetical properties and print quality are closely linked to coating ho- mogeneity and surface smoothness [32]. In the industrial production of dispersion-coated paperboard, the substrate is typically subjected to double or triple coating to improve sur- face properties and achieve higher coat weights. Industrial water-based coating equipment has largely been designed for high solids coating colours (coating dispersions) based on mineral pigments and synthetic latex binders such as acrylic and styrene–butadiene emul- sions. The solids content of such coating colours typically ranges from 50 to 70% (by wt.), depending on the paper grade and the mineral pigment and additives used [31]. The most common top-coating process is blade metering, in which excess coating colour is removed with a blade to achieve the desired coat weight [2,31]. In particular, bent-blade metering, where the bending of the blade results in a tip angle close to 0 ◦ , has been widely used in

https://doi.org/10.3390/coatings16030299

Made with FlippingBook Online newsletter maker