PAPERmaking! Vol12 Nr2 2026

Coatings 2026 , 16 , 299

4of 25

hydrogen bonding, leading to intercalation of starch and glycerol within the nanoclay gallery [67]. Exfoliation occurs below 2% bentonite, whereas intercalation occurs above this level [65]. The addition of bentonite increased the water contact angle of starch films, indicating enhanced surface hydrophobicity [66]. Furthermore, the permeability of water vapour decreased with increasing bentonite content [67]. Compared with starch films without bentonite, the addition of bentonite generally resulted in an increase in Young’s modulus and decrease in strain to break. [64,65]. However, it has been reported that the mechanical properties of paper coated with bentonite–starch–plasticiser formulations at low speed (laboratory-scale conditions) are predominantly affected by water absorption and drying during the coating process [62]. The oxygen permeability of laboratory-scale cast starch/montmorillonite films containing various plasticisers has been documented elsewhere [68,69]. Zeppa et al. [68] examined both a pure starch matrix and starch matrices plasticised with either glycerol or with a mixture of urea and ethanolamine. In all cases, the oxygen permeability exhibited a significant reduction following the incorporation of montmorillonite. Zdanowicz and Johansson [69] examined starch matrices plasticised with deep eutectic solvents. They found that the addition of small quantities of montmorillonite into the plasticised matrix increased the OTR, which then decreased as additional filler was incorporated. At five parts of montmorillonite per hundred parts of dry starch, the OTR of the composite matched that of the plasticised matrix without fillers. Poor barrier performance observed in pilot-scale coated paperboards can, at least in part, be attributed to the presence of coating defects, observed in both dispersion- and solution-coated paperboards [11,47,49,70,71]. A key challenge in high-speed solution coating is the relatively high viscosity of water-based polymer solutions, which typically limit the attainable dry solids content to around 25–30 wt%, as demonstrated for PVOH solutions [49]. To date, only a few studies have demonstrated high-machine-speed wet coating of starch–bentonite (or starch–nanoclay) dispersions onto paperboard for barrier applications. Tanninen et al. [72] reported a pilot-scale trial using a blade coating unit operated at 350 m · min − 1 , in which hyper-platy kaolin was utilised as the mineral filler. Menzel and Koch [73] presented the results from pilot trials using a starch–bentonite formulation and a hard blade configuration at 400 m min − 1 . Olsson et al. [74] described another pilot trial using a starch–bentonite formulation and a bent blade configuration at 500mmin − 1 . The overall objective of the present study is to identify and clarify critical process parameters governing multilayer coating technology with the dual aim of highlighting potential opportunities and describing a feasible process window. Emphasis was placed on drying strategies. It is anticipated that these results will form a basis for more detailed modelling in future research. This study is based on two hypotheses: • Firstly, the multilayer concept is expected to produce a contour coating profile—i.e., uniform fibre coverage with low variation in coating thickness—and to reduce defects within the coating layer; • Secondly, premature skin formation, pinholing and blistering are expected to decrease as a result of (a) a reduced amount of water that must be evaporated when apply- ing multiple thin layers and (b) the lower IR drying power required for such thin individual layers. The results of the present study clearly indicate that both coater design and the associated coating and drying strategies must be carefully optimised when producing barrier-coated paperboard from starch-based aqueous dispersions. Most publications on barrier-coated board production at industrially relevant speeds overlook drying as a critical process variable. The present study addresses this gap by systematically investigating the role of drying strategies within high-speed multilayer coating processes.

https://doi.org/10.3390/coatings16030299

Made with FlippingBook Online newsletter maker