J Renew Mater. 2025
11
EPW1 samples exhibited the highest average time to ignition (TTI) at 16 s, significantly longer than EPW2 (10 s), but not statistically different from EPW3 (12 s) (Table 3). EPW2 showed the shortest TTI among all samples, likely due to the incorporation of hemp shives into the substrate. Hemp shives are known to exhibit low TTI values (~11 s), consistent with the present findings, and contribute minimally to fire conditions when used in composite materials such as hempcrete [62]. The thermal degradation behavior of lignocellulosic components also influences ignition characteristics. Hemicellulose decomposes at 250 ○ C–370 ○ C, cellulose undergoes depolymerization above 300 ○ C, and lignin exhibits gradual degradation with major mass loss occurring above 380 ○ C [63,64]. The higher ash content in paper waste [42], and consequently, in EPW1 compared to the hemp (EPW2) and sawdust (EPW3) co- substrates, may contribute to delayed ignition. Additionally, the presence of mycelium may enhance fire resistance. Mycelium has been reported to exhibit flame-retardant behavior, including high char residue and water vapor release during combustion, offering potential as a sustainable, fire-safer alternative to synthetic polymers [65]. Time to flameout (TTF) is a critical parameter in assessing the fire safety of materials, particularly in construction, where shorter flame durations reduce the risk of fire rapid propagation. In this study, TTF val- ues for EPW mycelium biocomposites ranged from 595 to 963 s (Table 3). EPW3 samples, containing sawdust as a co-substrate, exhibited the longest flameout times, whereas EPW1 samples showed the shortest TTF. For comparison, sansevieria fiber-reinforced polyester composites have reported TTF values of 1883 s [66], while silicon-based composites composed of ash and silicone rubber display TTFs between 417 and 705 s [67]. The variation in TTF observed here is strongly dependent on the substrate composition. EPW1, consisting solely of egg packaging waste, demonstrates flameout times comparable to silicon composites but approximately three times lower than sansevieria polyester composites. Moreover, rigid polyurethane/polyisocyanurate foams demonstrate substantially shorter TTFs, between 69 and 175 s [68], emphasizing the comparatively enhanced fire resistance of the EPW biocomposites studied. Lower heat release properties correlate with improved flame resistance of materials. Among the tested samples, the EPW1 biocomposite, with egg packaging waste as the primary substrate, exhibited the lowest total heat release (THR) of ~12 MJ ⋅ m − 2 . MJ (Table 3). The inclusion of hemp (EPW2) and sawdust (EPW3) co-substrates increased the THR values, with EPW3 reaching 26 MJ ⋅ m − 2 . This may be attributed to the lower density of the co-substrate-containing composites. The influence of density on fire behavior has also been reported for bio-aggregate composites [69], where specimens with the lowest gypsum content exhibited inferior fire resistance compared to their denser counterparts. Similar THR values, ranging from 10 to 20MJ ⋅ m − 2 , were observed for lignocellulosic biomass insulation materials, which are lower than those of certain wood composites [70]. Elevated THR in co-substrate-containing EPW composites indicates a greater potential for heat release, thereby increasing fire hazard severity. Heat release rate (HRR) is a critical metric for evaluating fire risk, as higher HRR promotes flame spread. Peak heat release rate (pHRR) is particularly indicative of fire performance. EPW1 showed the lowest pHRR of 112 kW ⋅ m − 2 at 28 s time to peak (TTP), whereas EPW3 exhibited the highest pHRR of 165 kW ⋅ m − 2 at 23 s. EPW2 also displayed a higher pHRR than EPW1 (Table 3; Fig. 5). The addition of hemp or sawdust co- substrates increased the heat release and accelerated TTP. Shewalul et al. [62] reported that incorporation of hemp shives in hemp blocks reduced pHRR significantly, from 189 s to 23 kW ⋅ m − 2 , highlighting the influence of substrate composition. In comparison, sansevieria polyester composites demonstrated a markedly higher pHRR of 459 kW ⋅ m − 2 [66], underscoring the relatively favorable fire performance of the EPW biocomposites examined in this study. To ensure favorable fire-retardant performance, materials should exhibit minimal total smoke release (TSR) during combustion. Smoke contains fine soot particles and toxic vapors that can irritate the eyes and
Made with FlippingBook Online newsletter maker