4HANK YOU FOR PURCHASING THE 2OTARY $RYER 6ENT #LEANING 3YSTEM 0LEASE FOLLOW THE IMPORTANT SAFEGUARDS AND OPERATING INSTRUCTIONS INCLUDED WITHIN THIS MANUAL TO ENJOY THE CONVENIENCE AND DURABILITY OF OUR PRODUCT
,ONG m EXIBLE RODS screw together to reach into vents up to 12' from one end.
3ELF FEEDING !UGER "RUSH makes multiple turns in your vent.
6ACUUM !DAPTER Connect to a shop vac to collect the lint while rotary brushing.
"LOCKAGE 2EMOVAL 4OOL Removes heavy blockages and clears gutter downspouts.
,ARGE DIA ,INT "RUSH with Exceptional 42" Reach when connected to one flexible rod.
$RYER"LOWER !DAPTER Safeguards the blower wheel by stopping the Auger Brush when using the dryer air or a blower to remove the lint while rotary brushing.
• Read all safety & operating instructions before use. • All warnings in the manual should be strictly adhered to. • Failure to comply with the instructions & safety rules may result in property damage or personal injury. • Retain the safety & operator’s manual for future use. • Not all vents can be cleaned. It is sometimes necessary to replace or re- route the vent system due to improper material or installation.
1. To ensure safe operation of your dryer, it is recommended that the dryer vent system be cleaned 3 to 4 times per year. 2. It is also recommended that lint and other debris be cleaned from behind the dryer, the back of the dryer, underneath the dryer and the entire area surrounding the dryer 3 to 4 times a year or more often if necessary. 3. The lint screen should be cleaned before every load 4. The lint screen should also be washed with hot soapy water and an old toothbrush (or other brush) at least every six months to remove the film created by dryer sheets. 5. The lint screen duct, (the area that the lint screen slides or rests into), should be cleaned once a week .
rotate the rods in the
when spinning the rods
& coming • Failure to do so will cause the rods to un-screw and disconnect. • force the rods or over-torque the rods with the drill. Doing this may result in property damage, rod breakage or personal injury.
1. Only use a . (a cordless drill is recommended) 2. Keep clutch setting on drill at halfway or lower when rotating the rods.
• • Keep all loose clothing & objects tucked in to prevent them from being tangled around the rotating rods. • Add one rod at a time when spinning into the vent. • Never use the dryer to blow the lint out while rotary brushing without the included Dryer/Blower Adapter which will prevent the brush from rotating into the blower wheel of the dryer. • Failure to use the Dryer/Blower Adapter could cause damage to the blower wheel and also to the tool. Gardus,a HY-C Company, reserves the right to improve, change or modify the construction of thetools, including all attachments or any part thereof, without incurring any obligationto make these changes on previously delivered kits or accessories. Limited Warranty: The LintEater kit and all accessories are designed for homeowner use. All components are warranted for a period of one year from date of purchase. Should any part fail due to a manufacturing defect, return the defective part to Gardus and we will replace it free of charge. A return authorization number is required prior to returning any item. Gardus does not warranty failure of any part due to operator error. Be sure to read all operating instructions and safety precautions before operating any of the tools. Manufacturer accepts no liability for property damage or personal injury due to the operation of these tools and accessories. This is the full extent of the warranty made by Gardus. There is no other expressed warranty. All implied warranties are hereby excluded. R
Set on middle setting or lower
Any cordless drill with a 3/8” or 1/2” chuck with an adjustable clutch will work.
Setting the Clutch on your cordless drill a. Adjust clutch to a setting in the middle of the range or slightly lower. b. You should be able to hold the properly adjusted chuck with your hand & prevent it from spinning yet there should be a fair amount of torque.
Turn to adjust clutch
Connecting the Rods
Option 1 To connect the rods, simply screw them together and tighten with two pairs of pliers. Proceed to step 4 below. Option 2 This method requires a great deal of caution but will speed up the cleaning process.
1. Start the threads by hand to insure that they are not cross‐threaded.
2. Insert the other end of the rod into the drill chuck.
3. Spin the rods clockwise while holding the rod you are connecting to.
4. ALWAYS use a small piece of electrical tape or duct tape around the joint of the fittings after tightening.
Use Electrical Tape or Duct Tape to Secure Each Connection
Important : Always spin the drill in the Clockwise Direction as the rods may come apart even if tightened with pliers & tape is used.
Disconnecting the Rods
Hold end of rod very tightly by hand or with pliers
Option 1 Use two pairs of pliers to loosen & then unscrew the rods by hand Option 2 You can disconnect each rod using the drill as well. a. Hold the end of the rod, which is inside the vent, very tightly. b. Reverse the drill while holding the rod end to unscrew the rod which is connected to the drill. CAUTION! Be sure that the rods that are still in the vent do not spin as this will cause them to disconnect inside the vent.
Inserting Rods into Drill Chuck
1. The fittings on the rods are designed to fit into any type of drill without an adapter.
2. Simply insert the steel rod fitting into the chuck of the drill and tighten by hand
Twist chuck to tighten
Attaching Brushes to Rods
Auger Brush: Screw Auger Brush onto rod and tighten. Insert set screw into threaded hole in Auger Brush fitting and tighten using included hex key. (Use 8‐32 x 1/8”L set screw if replacement is needed) Lint Trap Brush: Screw Lint Trap Brush onto rod then tighten with two pairs of pliers. Use a small piece of duct tape on joint to help reduce the risk of brush unscrewing from rod. Important Note: Only use the Lint Trap Brush by hand. “Do Not Use the Drill to Spin.”While cleaning with the brush by hand, rotate the rod clockwise to ensure that the brush does not loosen.
1. Place the Blockage Removal Tool onto the rod.
2. Thread the included nut onto the rod.
3. Tighten with pliers or wrench.
Determinewhattypeofmaterialwasusedfor venting. 1. This can be done by looking into the exterior vent hood with a flashlight.
2. It can also be determined by placing the end of a FlexRod into the vent approx. 12 to 18 inches and tapping on the inside of the vent. Listen to the sound that the steel fitting on the rod makes when it contacts the inner walls of the vent.
3. White vinyl or foil venting will make a dull sound while rigid or semi-rigid venting will have a positive metal to metal sound and feel.
The LintEater is designed to clean all types of venting. However, extra care must be taken when cleaning white vinyl or foil. Caution! WhiteVinyl and Foil ventingshouldbereplaced withrigidorsemiͲrigidAllMetalventingif possible.
ͲIfthereis No airflowͲ go to step 4. ͲYes ,thereisairflowͲ go to step 7.
If there is a screen over the vent hood, remove it and do not re-install as it will collect lint.
IfThereis “NO” Airflow
Look for visual signs of a bird’s nest such as bird droppings by exterior vent hood. Also look for straw, leaves, twigs or anything else that is not lint inside the end of the vent.
Ifthereisabird’snestorotherblockage,usethe “BlockageRemovalTool”toremovetheblockage. a) Be sure that the dryer, vacuum or blower is turned OFF. b) Attach the Blockage Removal Tool to one of the flexible rods and insert into the vent, from the exterior, by hand. c) Add additional rods if necessary until you reach the blockage. d) Twist the rods in a clockwise direction while pushing the rods & tool into the blockage. e) When you have grabbed the
blockage, continue to twist the rods clockwise while you pull the blockage out of the vent. f) Repeat this process until the Blockage Tool can be pushed freely past the problem area.
Turn the dryer on again and check the airflow at the exterior vent hood.
STILLNOAIRFLOW? This may be caused by a more severe problem such as; - Disconnected vent - Crushed vent - Torn vent pipe, etc.
ImportantNote Ifsignsofamoresevereproblemexist,itisrecommendedthataprofessionalbe calledtotestthesystemwithspecializedtools.Oncetheproblemisidentified, theywillbeabletomakeanynecessaryrepairs.
IfThere “IS” Airflow
Tape or clip damper on hood in the open position or remove louvers on louvered vent hood.
Remove the louvers by bending them slightly in the middle. Caution! Be careful not to break the plastic pin on the ends of the louvers.
a) Turn dryer OFF & UNPLUG.
b) Pull dryer out carefully, especially if gas.
Clean area behind dryer as well as the back of the dryer itself using the Lint Trap brush and a vacuum
a) Remove vent from the back of the dryer. b) Hook-up a shop vac using the included “Vacuum Adapter” or attach an electric leaf blower to vent. Attachment can be made by using a piece of duct tape. c) Be sure that the outside vent hood is taped open before turning vacuum on!
If vent compresses when the vacuum is turned on, turn vacuum off immediately. This indicates a blockage or restriction in the vent and should be checked by a professional.
Cleaning From Outside:
1. Thread 4” Auger Brush onto flexible rods.
2. With the vacuum/blower running, go to the exterior and begin spinning the rods & brush into the vent. Important: a) Be sure the clutch is set on in the mid range (or lower). (See drill operation) b) ALWAYSspinthedrillinthe“ CLOCKWISE ”direction. c) Use duct tape on all Brush/Rod connections.
3. Connect one rod at a time until you reach the opposite end. Note: If your vent is longer than the included length of rods, finish cleaning from the opposite end. (Included rods will clean up to 18’ of venting when used from each end.
4. It is recommended that you spin the drill at a moderate to high speed while using a back & forth motion. 5. If the brush binds up, stop immediately. ImportantNote: Use caution and take your time to avoid breaking the rods or damaging the vent. NeverForcetheRods! AlwaysSpinDrillClockwise!
6. Once you feel you have reached the end, go to the interior, disconnect the vacuum or blower and look inside the vent to see if the brush has reached the end. If the brush is not visible, and you felt the brush binding up when you were rotary cleaning, it may be necessary to finish cleaning from the inside toward the outside.
Method1: 1. Continue to spin the rods in a clockwise direction as you pull the rods out of the vent.
2. Disconnect one rod at a time making sure not to
loosen the rods that are still inside the vent.
3. Attach the drill after disconnecting each rod to continue spinning the rods as you remove. Note: If you need to finish cleaning the vent from the inside, count the number rods used so you can estimate how far you have reached from the outside.
Optional Method for Removing the Rods from the Vent:
It’s also possible to remove all of the rods at one time by spinning the rods (always in the clockwise direction) and pulling them out of the vent as you walk away from the vent hood. (providing you have the room to do so and it does not present a safety hazard to you or the surrounding area) Try to stop when the brush reaches the vent hood. This will keep the rods & brush from falling and will prevent possible damage to the surrounding area.
Cleaning from “Inside” toward outside: This can be done by spinning the auger brush and rods from the inside toward the outside. Attach the Vacuum Adapter as shown. With the vacuum running, the loosened lint will be pulled back toward you and collected in the vacuum. Once you feel confident that you have cleaned the vent completely, you can remove the rods and brush from the vent as mentioned earlier. Important Note: The Vacuum Adapter is designed to fit a shop vac having a 2 ½” hose only. It is not recommended to use a shop vac or household vac having a 1 ½” hose (or smaller) since the lint being collected will continually clog the the hose.
Remove the tape or clip from the damper or re-install the louvers if you have a louvered vent hood. Be careful not to break the pins on the ends of the louvers.
Once the vent system is cleaned, connect the vent to the back of the dryer using the proper material. (Seefollowingsection)
Slide the dryer into place and plug the electrical cord into the outlet. Step16
Turn the dryer on and then go to the exterior and check for air flow. You should feel a higher volume of air coming out of the vent hood.
Connecting Dryer Vent
Replaceallwhitevinylorfoilventingwithallmetalventing. If you have white vinyl or foil venting behind the dryer or throughout the venting system it should be replaced with flexible metal or rigid metal venting. The following are some tips to help you install flexible metal venting from your dryer to the wall or ceiling. This section of venting is called the transitionduct. InstallationNote:
When installing venting components, the male end or (crimped end) must always face toward the exterior. This holds true for the entire venting system. Note: The following are only tips to help you with the installation. It may be necessary to call a professional to ensureproperinstallation.
Example of All-Metal Venting Components Used for Proper Installation
“Loop”Method: When used with the proper materials, this method will allow you to connect the venting to the dryer while it is pulled away from the wall. It will form a rounded transition from the dryer to the connection point of your venting system which, in many cases, is in the wall or floor.
Additional Cleaning Methods
Using the dryer to blow the lint out while rotary brushing
The “Dryer Adapter” has a built-in guard to prevent the rotating Auger Brush from entering the dryer thus preventing damage to the blower wheel within the dryer.
Pic of Dryer Adapter Hook- up from page 20 of current manual
a) Place the Dryer Adapter on the back of the dryer.
Pic of Dryer Adapter Hook- up from page 20 of current manual
b) Connect the vent to the adapter and secure with duct tape.
c) With the dryer running, go to the exterior and begin rotary brushing from outside as described earlier. Important: Be sure to remove the Dryer Adapter when you have completed the cleaning as it will collect lint if left in place during normal operation of the dryer. Note: Eye protection & a respirator must be worn as the loosened lint will be blown out toward you.
Usingan Electric LeafBlowertoblowtheloosenedlintoutoftheventwhile rotarybrushingfromoutside Method2
An electric blower can also be attached to the vent on the inside to blow the lint out while you rotary brush from the outside toward the inside. ImportantNote: a) Connect the Dryer Adapter between the blower & vent to prevent the brush from entering into the blower. b) Always wear eye protection & a respirator.
Rotarybrushingfromoutsidewith vacuumconnectedoutside This is not a preferred method but the cleaning can be done this way. ImportantNote: Only use this method with the DryerAdapter installed at the opposite end of the vent on the interior. This will stop the brush when it reaches the end of the vent.
Additional Cleaning Methods
Rotary brushing from inside with vacuum connected outside
a) Connect the vacuum hose to the exterior vent hood.
b) Rotary brush from the inside toward the exterior while the vacuum collects the loosened lint on the outside.
Cleaning by Hand from the Inside or Outside
a) Thread 4” Auger Brush onto flexible rods.
4. Rotate rods in a clockwise direction while using a back and forth motion to remove the lint from the dryer vent. Included rods will clean 18’ of venting when used from each end. Note: A shop vac, electric leaf blower or the air from the dryer should be used to remove the loosened lint while brushing the vent.
Cleaning Lint Trap & Lint Screen Duct
Works for dryers with lint screens in the “Top” of the dryer (as shown) & for dryers with lint screens inside the front door! 1. Always “scoop” the lint up toward you when clean the lint trap area. 2. Use a vacuum to remove the lint from the brush as you pull the lint up & out of the Lint Trap.
Bend brush for more versatility
Clean the Dryer Interior
Although cleaning the dryer vent system is extremely important, it is equally important to clean the
inside of the dryer as well. Only attempt this if you are
familiar with taking dryers apart. Otherwise, it is recommended that a professional be called to periodically clean & inspect the interior of your dryer.
Cleaning baseboard heat or under refrigerator with the Lint Brush
Baseboard Heat: Works great to remove the dust buildup on the fins inside your baseboard heat. Simply run the brush over the fins while the brush clockwise. Use a vacuum to clean the brush as you go. Be careful not to damage the fins.
Under the Refrigerator: When
to one or more FlexRods, the lint brush also works great for cleaning out the debris from under the refrigerator or any hard to reach areas around your home.
Use Blockage Removal Tool for clearing er Downspouts” a) h the Blockage Removal Tool to a rod as b) Feed the first rod with the tool up into the
of the downspout.
c) to add rods un l you reach the blockage. d) Use your hand or the drill to rotate “Clockwise” into the blockage it is cleared. The tool can also be used from the top as well.
What to do if the rods disconnect in the vent
If you accidently reverse the drill or rotate the rods “counter clockwise” by hand, the rods may disconnect leaving some of the rods and the brush inside the vent. Although this rarely happens, we have designed a “Retrieval Tool” to grab the brush and pull it out. It aches to your remaining rods and is used by hand without the drill. To obtain this tool, please contact us at:
firstname.lastname@example.org Phone: 203.985.0208
Additional Products from
12' Extension Kit Adds to your
Rotary Dryer Vent Cleaning System for vent runs
longer than 12 feet.
Includes: 4 - 3' long Flexible Rods
L int C atcher ® Captures loosened lint from the dryer vent while rotary brushing with the
System! Simply attach the LintCatcher™ to the exterior vent hood, turn on your blower or dryer and begin rotary brushing the vent system. As the loosened lint is blown out by the blower or dryer air, it is collected in the LintCatcher™ making your job clean and hassle free. Works great when cleaning from the outside or from the inside! Easy to use
Attach the clips PositionLintCatcher over the vent
Secure with drawstring
How to Purchase Accessories & Spare Parts
If you would like to purchase additional accessories or spare parts, please go to www.linteater.com then click on the “Where to Buy” tab. Thank You
800-325-7076 (toll free)
www.gardusinc.com www.hy-c.com Made in ChinaPage 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48
Made with FlippingBook - professional solution for displaying marketing and sales documents online